Installing snowstores on the roof of metal tile: installation according to your own instructions. How to install snowstands on the roof from the corrugation? Correct installation of snow soverees on the roof

Strange devices on the roofs of houses are increasingly falling on the eyes, similar to double handrails, but installed unusually close to the roof surface. These are snowstores - special devices for holding a snowy layer on the roof. In the area where a large number of snow falls, all more people Prefer to install snowstanders to be confident that the accumulated snow will not cover you at the most inopportune moment.

What give snow-setpoints to protect the roof

The design device of the snowmobile designer was highlighted from Finnish builders, and today copies of original and modified options can be found on sale, ranging from specialized salons, ending with conventional construction markets.

The need to install on the roof of devices delaying the snow reservoir until the critical reduction to acceptable sizes is not necessary to explain to anyone:

• First, the installation of high-quality snowstores on the roof allows you to protect all those who are forced to pass under the roofs;
• Secondly, the snow held helps reduce heat loss through the roof;
• Thirdly, with the proper execution of the roof and water collectors, the melting snow is gradually leaving in the form of melting water in storm sewer.

Important! The use of snow concreteners with too small angle of inclination of the roof leads to the fact that snow load On the roofing can exceed the strength of the frame and the rafted roof. In this case, it is necessary to forcibly remove the snow using a pneumatic cleaner.

With a too big angle of inclination of the row of the roof of the minillavin, it can easily break a snow-setthel, especially if the device model was selected disproportionately under the existing load. 20 cm with a 20 cm thick layer on a 5-meter width of a width of 4 meters can reach tons, which, even taking into account the slope of the roof, can affect the design of a snow-settker with a force of several hundred kilograms.

Choosing and installing snowstanders on the roof

The type and dimensions of the snow-setpore on the roof should correspond to the type of roof, the angle of inclination and the maximum thickness of the snow layer, which can be kept by the device. As a rule, everything that exceeds the height of the snowman, comes from the roof and is demolished by the wind.

By the types of design, snow-settresters for the roof can be divided into several categories:

1. Snowplows for a soft roof. The simplest swing or hook devices in the form of single supports distributed on the roof slide area, usually at its lower part;
2. Plate or corner snowstores. The principle of operation and device are similar to previous optionbut possess a large stopping effect;
3. Tubular or frame sneakers. The most difficult and most effective for most types of roofs based on galvanized metal.

Tip! When choosing a symbulator type, the first criterion should be the quality of the manufacture of the device, and not the type or method of its installation.

How effective are simple snowstanders on the roof

Simple designs of snowstores are not less popular than heavy tubular or lighter corner structures. On the device, such a type of snow-setholders would be more correctly called distributed, since, unlike the last two schemes, the individual elements of the hook snow-coaster are installed throughout the area of \u200b\u200bthe roof slide.

In this case, the load from the pressure of the snow cover to separate hooks is transmitted to beach beams And the roof crate is more evenly, which allows you to install devices on any types of roofs. The most effectively such type of snow-setpower works with soft roofhaving a rough surface due to peas sprinkles.

Montage of hooks is easy to perform with its own without the involvement of specialists, you only need to choose and place the installation points and secure them on the roof of self-pressing with silicone gaskets or the swelling of the sealant. The breakdown of one of the hooks reduces efficiency, but does not lead to a catastrophic one of the snow.

The disadvantages include the need to punch a soft roof in many places of the roof. This significantly worsens the resistance of the soft roofing canvas to the moisture flow.

Corner Snowplows on the roof

A more advanced design can be considered corner snowstores. The principle of operation of such an element is similar to the previous one, with the difference only, instead of a single "shoe", a set of slats or angle installed by lines or steps is used. In most cases, the possibilities of such a snowstore are higher than hooks. This is due to a significantly larger surface of contact with snow cover than the previous version.

The design of the corner snowstore is very simple, most often it is stamped from thin-leaf galvanized steel profile of a pyramid. The profile height can reach 7-10 cm. In this case, the roof frame accounts for a relatively low load. Whole snow, the thickness greater than the height of the snowmaker, slides on the roof slide.

The corner snowman is easy enough to fix on the roof of any type. As in the previous case, each element is attached to self-drawing to the roof crate. In the most simple cases, the devices are mounted in the form of a torn step line at the bottom of the skate. To increase the symbulatory efficiency, the corner option may fit on the roof by several lines or placed in a checker order.

The disadvantages of such a type of snowmobile supporters include the need for competent calculation and determination of the optimal places for the installation of individual corner elements. During the melting of snow of this kind of snow-setting system, water flows on the roof can redistribute the efficient operation of drainage and catchment gutters.

Snowstanding devices based on tubular elements

Tubular devices for holding snow on the roof have become a classic sneakeholder option. Structurally, such a snowman is a pair of tubular elements installed on the brackets along the edge of the roof rope. The distance between the pair of pipes is no more than 15 cm. The layout and general view of the device is well read from the diagram. Manufacturers recommend setting such snow-holder systems throughout the perimeter of the roof, but in reality, the hosts are limited to one or two assemblies for reality of savings even for large and long rods.

Each bracket has several holes in which a tubular element is installed. In the simplest and cheapest structures, the elements of the circular cross section, in high-quality and more expensive - an oval or ellipsed section is used instead of the round. This provides an almost double increase in rigidity and strength in the transverse direction with the same wall thickness. In addition, the high-quality profile is manufactured with a wall thickness of at least 1.5 mm with mandatory zinc, priming and an epoxy-based enamel.

In cheap elements, as a rule, the metal is phosphatized and is painted by conventional alkyd enamel. The service life of such a snowstaving device is determined by the rate of corrosion of the surface of the pipe coming in contact with the bracket. As a rule, it is two or three years.

Bracket has a reference plane in which 6-8 holes are made through which the node is attached to the roof surface. Thus, when installing, you can pick up the most suitable hole to get a screw in the screen of the crate.

Most of the options for professional or metal tile has a regular relief on the surface in the form of waves and ledges. To align the position of the bracket, a certain number of gaskets, compensators is always attached. Mandatory condition is the use of a sealant that ensures the waterproof of the hole with a self-tapping screw in the roofing material.

The brackets are set at a distance of 90 cm from the edge of the roof with a step of 100-110 cm. Installing brackets is the most complex operation on the installation of a symbulator system. From the reliability of the attachment of the brackets to the roof depends the strength of the entire design of the snowmobile.

Conclusion

In some cases, especially when installing cheap Chinese variants, the wizards do not always be attached to the bracket directly to the crate board, but leave the self-tapping screw, screwed into a thin sheet of metal. As a result, a weakened design is obtained, which can be easily cut even with a relatively small layer of snow.

Unlike Chinese tubes, Finnish and even domestic tubular snowstores are able to withstand a large load on the roofs with a slide length of more than four meters.

It was established that on the roof of the house with an area of \u200b\u200bonly 40 square meters. M may accumulate about 5-8 tons of snow. If there is no snowstore on the roof, you can imagine what will happen with a person passing by by a person when a huge force of snow suddenly collapses him. In this case, the owner of the house may be punished, up to criminal liability, because according to the laws russian legislationThe property owner is fully responsible for the nearby territory of his housing. In addition, snow gathering can cause serious damage, both personal property and someone else's.

Types of snowmates: corner, lattice, tubular.

Some do not give much values \u200b\u200bto anti-bomb devices, worrying about the fact that they will spoil the design of the roof, but in fact it is an erroneous, since such systems will bring down the finishes on the contrary. Due to the fact that snowstores are security devices, it is impossible to neglect their installation. Accordingly, many will have a question how to establish snow-sauers on the roof correctly, because everyone does not have the opportunity to hire costly specialists. Moreover, sometimes the price for their services is much higher than the cost of the device itself. Before proceeding directly to the installation of snowmates, you should figure out what types they are divided.

Types of snowdown systems

1. The lattice snowstores are most sought-after, since they are considered the most effective. This is the best option, both for high-rise urban homes and country private ussers. An important advantage is that this type of anti-binding device can be installed almost on any roof, regardless of which roofing material it is covered. This system is usually made of metal and has a lattice. Fasten it either on suspended or on naval supports.
2. On the roof of the mattalchoolerpitsa and the professional flooring can be attached to lamellar (corner) snow-saw holders, which are made of the same material as the coating. This is the most a budget option. However, their installation is possible only on the roof, which does not exceed 30 degrees, otherwise they will be ineffective.
3. Snow walls outwardly very similar to the hooks. Installation of snowproofs is carried out mainly on roofs with soft roofs or they are used as additional elementsreinforcing security in winter. Currently, they began to produce from transparent plastic, which makes them imperceptible.
4. Tubular snowstores are not inferior to the lattice and are a versatile, modern and highly efficient device that prevents the sudden gathering of snow from the roof. This design is a compound of several pipes with special bracket supports. They can be installed on the roof of the profile, tiles, and also this is a great option for a folding roof.

Thus, it turns out that the most optimal options There are two types of anti-bomb systems: lattice and tubular.

For someone, the first system is suitable, and for some - the second. But to set the selected snowstore on the roof, you need to know that there are individual installation rules for each species. If it is decided to produce it yourself, then it will be necessary to stock up the standard set of tools that is suitable for installing both devices. It includes:

• stairs;
• drill;
• screwdriver;
• roulette;
• a hammer;
• level.

Rules for installation of tubular snow-holders

Diagram of installation of a tubular snowmobile.

Installing these anti-bunny systems can be installed both on the roof under construction and ready. They can be located on the roof in a checker order and horizontally into one or more lines. Install them above the attic windows, entrances or pedestrian walkways. In no case cannot be placed over the cornese sve.

Tubular snowstores are attached perpendicular to the crate with special brackets, which in addition to the fastener function, play the role of a uniform load distributor on slinge systemthat prevents the "breaking" of snow feet from the roof. Immediately the brackets are fixed by metal screws. They should be located in places where the bearing walls are located. The distance between the attachments directly depends on the angle of inclination of the roof and the length of the skate. This is usually somewhere 0.5 m or 4 mounts by 3 meters. Mount them follows the joint into the joint, while it is necessary to set them exactly in terms of the level.

If the slope on the roof is long, then such security systems must be installed in several rows. When the installation of tubular snowstores is carried out, rubber washers should be placed between roofing material and supports. Such a measure will allow to ensure tightness in places where fasteners passes and prevent leakage. In addition, such washers allow you to adjust the installation plane.

Rules for the installation of lattice snow holders

Recently, with the advent of tubular systems in private construction, lattice snowstores are increasingly used for tiled roof. To set the lattice systems, you need to purchase universal or suspended, or naval supports by which they are placed on the roof. The feed supports are attached to the roofing clamp by self-drawing, and suspended - by hanging on the crate, with the help of a special metal hook. Unlike other snowstores, the lattice systems can be installed directly along the edge of the eaves.

Professional flooring is one of the most popular coverage materials for roofs. Corrugated metal is easy and cheap, but at the same time very durable and durable. But on a slippery metal, the snow is not holding at all, especially the lifting and heavy. Therefore, many owners of private houses with such a type roofing Install on the roof of snowstores for a profile.

Snowmobiles on the roof are divided into 2 main groups:

• Snow-plates, crushing the layer of snow on small fragments, which, when falling to the ground, will not harm anyone. Such designs are suitable for low houses, or regions where there are few snow falls;
• Snow-boarar, which blocked completely gathering of ice blocks from the roof of the house.

On the roof of the professional flooring can also be used snow-planes, and snow booths, depending on which function must be performed. The lack of snow-holders is dangerous even for the roofing coating: scratches on metal sheets can remain from the alignment of a large snow mass, breaking the drainage system, and if the snow mass is distributed unevenly, for example, with sunny side It will come down, but with the shadow - no, the roof can only shift.

Snowman design different types Approximately the same. The device consists of a bracket that is attached to the roof material, and the platforms on which the basic pressure of the snow mass. As a rule, the design is very simple, and therefore reliable, and can withstand weight large number frozen water.

Types of snowstanders for professional flooring

Snowmaders for professional flooring can be one of the following types:

• Corner snowstores. These devices are the simplest in design and affordable. They constitute a metal strip, bent along half and fixed on the roof. You can even consolidate them on top of the roofing coating with your own hands. Corner snowstores on the roof are manufactured different colorsso they can be selected for the color of roofing;
• Tubular snowstores. Drubned snowstores on the roof are perfect for a profile. This type of devices is designed to hold or crushing the large mass of the somewhat snow. Thin tubes of this design are fixed on the bracket, and the bracket itself is attached to the roofing rod using metal screws. The lower boundary of the tubular snow is usually done by 2-3 cm above the roofing coating, and the distance between the tubes should be 8-10 cm.

Usually, tubular structures are installed in a row at a distance of a feet from the edge of the skate, so that heavy snow mass does not cause a visor. If the snow falls a lot, and one snowmobile will not be able to keep a convergent avalanche, the designs are installed in two or three rows, at a distance of 2-3 meters from each other.

Golden snowstores

The lattice snowstores are universal, and therefore they are considered one of the most common. It is possible to install such structures on the soft roofing coating, and on the roof of profiled sheets.

The popularity of this type of snow-resistant and decorative properties. The grille that performs the basic function in the Snowpora device may not only be a simple functional part, but also an exquisite decoration of forged metal.

The lattice snowstores can be installed on the roof without self-tapping screws: suspended brackets Mixed to the crate, and profiled sheets are stacked over the fasteners.

Snowmaders on the roof can be another design, for example, buffered or made of logs and hooks, but such structures are rarely used for professional flooring due to their ineffectiveness.

Choosing and installing snowstanders on the roof of a corrugated floor

Snowbornels for professional flooring should be selected individually for each house. When developing the installation scheme, their installation must be taken into account:

• Roof coating material;
• Bias of the surface;
• Roof area;
• Climatic features of the region;
• House location;
• The purpose of mounting a snowstore device.

On steep roofs, in high buildings, many people have a lot of people, or in the regions where a lot of snow falls out, the snow-pot must be reliable that even small pieces of ice and nasta fell down. If there are little snow for the winter, and it flies exclusively to the site where there are neither people nor cars, it is possible to install snow-skinned.

As a rule, on the roofs, the skate of which is steeper 60 degrees, snow mountains are not installed at all, since the snow does not delay them.

Snowmobile supporters for professional flooring it is better to choose those that are made of stainless steel or galvanized iron. These materials will serve for a long time and will not suffer from corrosion.

Tubular and lattice snowstores for professional flooring are set approximately equally.

First, the roof marking is carried out and it is checked how firmly the roof is cloudy with the crate. If the rafters are reliable and profiled sheets are attached hard, then you can start building construction.

First, brackets are collected, which are attached to the roofing coating by self-draws. It is advisable to use special self-tapping screws to work with profiled sheets, and if there is no, it is necessary to install rubber gaskets for fastening so that the water from the melting snow and rains do not fall on the metal. The brackets to the lower part of the wave are attached, that is, that part of the sheet that adjoins the rafters, as it does not deform the sheet, does not harm roofing, and provides structures high strength.

Pipes are inserted into the collected and attached brackets or the lattice is attached to them. The design is fixed, and if necessary is covered with water pumping paint. Snowbornels on the roof are quite simple, and the installation can be done with your own hands.

Corner snowstores are installed differently. Because they are intended to slow down the fall of a small mass of snow, then the same reliable mount, like tubular, they do not need.

Corners are fastened with screws for metal for the edges of the steel strip to the top of the metal profile wave. Usually they are installed on the roof in two rows in a checker order, at a distance of about half a meter from the edge of the skate.

Security measures

Since thanks to the snowmobile toaster, the whole mass of the lowered snow will remain on the roof, then both the roof, and rafters, and the walls must be prepared.

It is impossible to perform the installation of snowfoot on the visors and hanging the edges of the roof, since these parts of the roof may not withstand the weight of the snow and collapse with it. Snowpora post only over carriage wallswhich are able to withstand the mass of frozen water. It is also necessary to strengthen the rafters and beams on which professional flooring is kept, you can do it with your own hands.

Installed snowstanders on the roof do not exempt the owners of the house from the need to drop snow from the roof.

On the contrary, the pressure on the roof of the mass of frozen water will increase repeatedly, since now the falling snow will not roll on the ground itself.

To get rid of the need to clear the snow drifts on the roof, many builders are recommended to stretch under the roofing material, the heating cable that will heat the roof. In this case, melting snow will be drained along the waterproof, without burdened by the owners of the house.

Properly installed snowstores on the roof will protect and residents at home, and random passers-by.

This simple and inexpensive design can be collected with your own hands, and such a device will be no less efficient than the expensive store.

Even the easiest snowman installed on the roof will help protect passing people under the houses of cars and landing near the walls from the fall of snowy blocks from the roof of the building.

In Russia, enjoy more popular scope roofson which snow is not delayed. However, the problem of steeply rods is a spontaneous gathering of snow masses, threatening health and even the life of people passing by people. More others from this suffer roofs from materials with a smooth surface, in particular, the proflist. To prevent snow cleavage, apply special devices, in everyday life called snowstores. This article will tell what kind of synchtercing measures are applied to the roof from the corrugated floor and how the installation of devices that prevent snow cutting are carried out with their own hands.

Russia is famous for frosty and snowy winters, and in some regions the cold season lasts 8-9 months. The snow accumulating on the skates increases the load on the rafter frame and the foundation of the house, so most buildings are built with a steep roof, the slope of which is at least 35 degrees. And if a straightening, material with a smooth, slippery surface is used as a roof covering, then the snow is immediately clench. Warm airRising up from heated premises warms the roof, due to which ice crust is formed on it.

Snowbornels installed by their own hands, save homeowners from the following problems:

1. They delay the snow masses on the roof of the corrugated floor or the proflist, while they do not melt under the action of the sun. In this case, melt water falls into the drain, and then into the storm sewer, without eroding the basement of the foundation or the suitable paths.
2. Snowbornels cut the snow cap on the roof from the professionalist, on thin layers, the drop in which will not harm the random pass.
3. The installation of snowstanders protects against the deformation of the roof of the roof from the corrugated floor, preventing the sloping of the snow masses there.

Important! The ice crust formed on the roof from the proflist because of the lifting of the lower layer of snow, the surface of the roof scratches the surface from the skate. These scratches are later in the penetration of water will become corrosion foci, leading to premature destruction of the material. This problem is solved with their own hands by installing snowstores.

Principles of snowstand

Usually devices for holding snow on the roof are selected to the roofing coating in color and material. Manufacturers producing professional flooring and professional owl, usually complement their products with snowstorming elements, which are divided into two types according to the principle of operation:

If the roof has a coating of a corrugated floor, it is necessary to install devices that prevent the elemental gathering of the snow masses. Since their absence creates a danger to the health of the inhabitants of the house and makes harm to roofing, reducing the service life of the material.

Views

Setting snowstores - the process of creating a physical barrier from a durable material capable of stopping and keeping a snowy mass on the skate. The view and number of snowstand elements depends on the amount of precipitation, slope and the type of roofing coating. For roofs from the professional leaf, the following models use:

Note! Usually builders recommend to install snow retention elements with their own hands along the entire ride slope, but this undertaking is associated with serious financial costs. To reduce costs, perform only on particularly important sites: driveways, parking, porch, green plantings. If the length of the skate exceeds 5 m, then the installation is recommended in two rows.

Installation

By mounting from the professionalist with your own hands, you should consider this task with attention. The fasteners disrupt the integrity of the roofing coating, so they use roofing screws with a press hat and a rubber seal. Installation technology sees as follows:

Important! The entire snowstand device is experiencing a huge load, so they should be made from high-quality metal. Each bracket is fixed at least three roofing self-drawers. If the installation is careless, the snow cap is a large mass of snow-settresters, deforming the roofing coating.

Experienced roofers recommend the installation of tubular snowstores, which are suitable even for very steep roofs with an inclination angle of more than 60 degrees. Good efficiency is demonstrated by hybrid devices, which are a grid, welded to the tubular elements of snowdown. To save you can make them with your own hands.

Video instruction

Types and installation of snow concreteners on the roof

Winter time is a serious test for durability for any kind of roof. Snow masses accumulate, form "caps" and under the influence of temperature drops turn into ice boulders and icicles. However, over time, the snow begins to fit, the climatic features and the heat outgoing from the roof are affected.

During this period, the concerns of the snow masses carry a greater danger, first of all for the life and health of people. The integrity of the property is a minor moment, but this is no less important.

The competent installation of snowstores on the roof of the metal tile and the professional leaf ensures the crushing of snow formations and their simultaneous retention. Subsequently, the accumulated precipitates go with roofing in the form of small fragments, which is safe for others.

Types of snowmates and their purpose

Modern constructive decisions Snowmobiles for the roof are divided into two types - bandwidth and barrier. Installation of snowstanders on metal tile, as well as on a different type of roofing, should be made according to individual marking. The zones of the alleged large accumulations of the snow masses are calculated taking into account the roof geometry, in these places, snowballs are installed in two rows.

For purpose

Barrier systems are more suitable for regions, where precipitation is not active. Thus, the accumulated snow masses are delayed on the roof and melted under the influence of sunlight.

The bandwidths, as already mentioned above, provide separation (crushing) of snow chains and looked outwards into separate small parts. As practice shows, it is bandwidths that are most in demand.

By structure and modification

By its technical modification, these designs are divided into lattice and tubular options.

Snowplows:

• lattice;
• tubular;
• log shape;
• corner;
• bougiel (Point Snowswear on the roof), hooks.

In addition to its direct destination, snow boosters facilitate the process of cleaning snow from the roof. When conducting roofing work Or with squall wind hold fragments and details of the roof from falling. They also minimize the risk of damage to the facade of the building with falling icicles and snow, protect the drains from the sera. The type of roof, the type of roofing and the climate features determine the selection of snow concreteners.

How to install snowstanders on the roof of various types

Tubular and lattice structures are considered universal. Snowstanding on the roof of metal tile, the proflist, rolled materials is equally possible on all types of roof. Constructions are distinguished by reliability, they can be installed on the roofs with a large tilt angle.

Gold and tubular

Such snowballs are able to withstand the essential weight of the snow masses. The big plus is the ability to install data of structures both on a new roof, in the construction process and on the already exploited. The specificity of the attachment involves the installation of the brackets through the outer coating to the roof cutting - the bottom-in-mount method.

The length of the brackets varies from 30 cm to one and a half meters, if the elongation is necessary, the pipes are joined. The lattice analogs are lengthened by adding sections of the required length. This type of snow-mounted is mounted either in one row or in a checker order.

Corner and lamellar snowmobiles on the roof photo

These roof snowstores are optimally suitable for fastening on rigid roofing types. It can be metal tile, professional flooring, galvanized. Construction fastening is made both during the installation of a new roof and on operating.

Snowplowed on the roof of the corrugated floor is made by fastening into the top wave of roofing sheets. Therefore, such structures are designed for small snow loads and are recommended for installation in regions with temperate climates.

This kind of snowman is a type of lamellar analogues, their installation is performed using special roofing bolts with rubber gasket. In most cases, the design is sold already equipped with all necessary details, gaskets and self-drawing.

It is worth noting that corner and lamellar snowstores do not differ in great strength and cannot hold the high weight of the snow. If the angle of inclination of the roof (skate) is less than 30 degrees, then you should not install them.

Loggy snow booths are the most longtime way to hold snow masses on the roof. It is rarely applied today, but still relevant from lovers of characteristic design and architectural style that resembles Bavarian and Alpine buildings.

This type of snowstores is distinguished by reliability and high efficiency, since the powerful pipe (or log) is able to hold very heavy loads. Today you can rarely meet exactly wooden barperforming the role of the barrier, most often used metal pipes with a diameter of about 140 mm. Supports for log holders are made of steel sheets and have a simple fastening system.

Snowy Poppers

As for snowstorming bohegels (snowy walls), they do not differ in particular reliability and often act as auxiliary elements. They interact with any snowstore designs and are installed at a distance of at least 80 cm from the roof edge.

By installing snowstores to the roof with their own hands, you should observe the limit caution and safety rules, and place them evenly throughout the roof inclination area. Bohels provide a peculiar point retention of snow masses, made by stamping and are suitable exclusively for metal and professional-floor coating.

Separately, it is worth mentioning the safety technique. The installation of snowstanders on the roof of the corrugated is the process of responsible and traumatic. Special stairs and roofing ladders with perforated surface will make it easier to move even on the roof and significantly reduce the risk of falling.

Installation Safety

By installing snowstanders on the roof from the professional leaf, metal tile or other material, consider the sliding factor, as it is always present. The entire workflow occurs at the height, so be sure to take care of the appropriate protective fence and fastening.

By installing snowstanders, use:

• fastening belts;
• insurance cable;
• anchor lines on the edges (temporary fastening limiters for the installation of the cable and as a protection during a slide fall);
• special shoes with non-slip sole.

Optimal decision will be the installation of snow-breeding during the arrangement of the roof or overhaul. Defined with the type of arrests and buy component parts to them best together with the purchase of roofing materials. Pay attention to high-quality and perfectly proven designs from Borge (Sweden), ORIMA (Finland), Ruf (Russia).

In turn, snowstores for metal tile and other roofing materials from domestic companies "Steel Partner" and "Metal Profile" can be made in any preferred color for you. As mentioned, the installation of these structures is allowed at any stages of the roof operation, but it is most convenient to do this with initial installation or repair work.

First of all, the choice of materials should be based on climatic factors in the region, as well as on the individual characteristics of a separate roof. The longer the winter and generous for precipitation - the most reliable the system of snow-melon.

Outcome

If the number of snow is slightly, and he has time to melting until the next snowfall, it is enough to install corner barriers. Well, if the winter in your region feels like a full mistress, then reliable mesh and tubular systems will successfully cope with icicles, looked out of the roof and snowflowers. In addition, this type of design ensures comfortable and safe hand work to remove snow masses.

Installing snowstaving systems will be relevant and repaired old roof, and when erecting a new one. The presence of snow holders will ensure the necessary security and give the general view of the house architectural completion.