Snowstanding on the roof from the professional flooring with their own hands. Snowmobiles are a modern security system and comfortable roof service. Advantages of installing snowstanders on a roof from a corrugated floor

In those regions where a moderate climate is present, and a large number of snow falls out, scope roofs Present for people a greater danger. It is related to the fact that a large mass of snow accumulates on the roofs, which at any moment can collapse down. Moreover, if the roof of the house is covered with a professional flooring, because the metal sheet has a high thermal conductivity. So, the heat emanating from interior premises is freely reaching the snow. Its bottom layer begins to melt, forming between the smooth surface of the professional sheets and snow, water layer. It is the latter that becomes the reason for the purpose of avalanche-like a huge volume of snow.

To this not happened, special devices are installed on the roofs of the professional flooring, which wear snow-setpoints. It should be noted that these important devices perform and additional functions. Without them, unpleasant consequences of another plan may occur. Namely:

Dissoli or even the destruction of the rafter structure of the building due to the change in the uniform distribution on the roof from the snowstock profile.
Part of the roof, which is located below can be destroyed. Because the volume of snow falling down can have a huge amount and mass.
A drainage system can be destroyed.
Damaged landing near the house and damaged personal property of people, for example, cars under the windows.

All this can be avoided if installing from the professional flooring. It is they who will restrain the mass of snow regardless of whether he melt or not. At the same time, the uniformity of snow cover will be observed throughout the area of \u200b\u200bthe skate.

Attention! Remember that the installation of snowmates is the ability to prevent snow gathering, and respectively get rid of many troubles. But this does not mean that the roof of the professional flooring should not be cleaned. It is necessary to do so with frequent consistency, this is especially true of the regions where big precipitation falls.

Types of snow feet

Modern snowstores are wide enough the lineup Mainly manufactured from metal profiles. By the way, make a snowmaster do it yourself not a problem. The main thing is to choose the easiest and most reliable option.

Tubular

This is the most frequently used model and quite popular. The thing is that a tubular snow-coaster is not just a restraining device, with its help you can gradually reset, not harm. That is, the snow passes between pipes of portion of a little weight and falls from the roof from the corrugated floor. This reduces the load on the roofing design. Therefore, experts believe that this version of the snowstore is the most effective.

We add that the pipe structure has high strength. They are usually installed directly at the level of the wall at home and attach to the roof by self-drawing through professional flooring. That is, the installation of the device is very simple. In the event that the height of the skate exceeds 5.5 m, it is recommended to install pipe snowstores to several rows.

Currently, many manufacturers produce that tubular structures. But more and more often, these models were advertised on the market, in which the pipes are not circular cross section, but oval. Engineers calculated that this option is more reliable, it perfectly copes with huge loads and pressure of snow cover.

Platery

The design of this model is very different from the previous one. But on the market it is one of the cheapest options. In fact, it is a perforated metal plate installed on the brackets. Like a tubular device, it is installed in the roof cornice. An important component of lamellar snowstores is the thickness of the material used. What it is thicker, the more reliable the device. Of course, fasteners connecting the plate and bracket must be high Quality.

But manufacturers warn that lamellar snowstores cannot restrain the large volume of snow. Therefore, it is recommended to establish them on roofing with an angle of inclination no more than 30 °. Often you can meet these models made from the same professional flooring.

Grident

This version of snowstores is simultaneously the easiest in terms of construction, and the most effective in the plan to contain snow mass. As for the design, the lattice devices can keep even small pieces of sleep. That is, it turns out that these structures can hold on the roofs of a large volume of snow on the roofs. So, their installation is possible only on roofing with a large bearing capacity.

The most amazing thing is that directly to the roof of the house, these snowstores are not attached. For them, additional suspended nodes are needed. They are mounted without self-tapping screws to the roof shabby, and snowstores are installed on them. There is another type of additional feed-type devices. They are naked to roofing material, but in this case this material should be soft.

Bent (corner)

Honestly, not the most successful soverees. It's all about their design, but, more precisely, in the profile used for making a profile. In fact, it is a metal corner or, bent by profile, a chamber. If you argue logically, this is not a snowman, but a barrier, through which can not pass anything. Such a device holds back the large masses of snow, but does not withstand huge pressure. So with a lot of precipitation, the bent snowdowers quickly fail.

Therefore, experts advise to mount these structures on the roofs with a slope of no more than 30 °, but better in the regions where snow falls in small quantities.

Point

This symborate holders appeared on the market relatively recently. It was specifically invented for roofs from a professional flooring or metal tile. These adaptations are made of galvanized steel, as well as professional flooring itself, almost all models are covered with a polymer layer, which increases their life. Manufacturing technology - stamping.

Attention! As for the installation of point snow-holders, their installation is made on the crest of the wave of professional flooring, and the fastening is not for the wooden elements of the roofing system, but to the metal surface of the professional flooring.

Of course, today it is impossible to say that these are the most effective models. But the fact that they are better than some can already be. In any case, the point setup reduces the load on the roofing design and prevent the avalanche-like snow. After all, through the snowstone to pass part of the precipitation.

Homemade

Embodiments of homemade snowstores a huge amount. Most often, they are made of metal corners, often use pipes. An important component is the strength of the structure itself, therefore the one who makes the roof repair from the corrugated floor and is going to make snow-holders with their own hands, must own the skills of working with electric welding.

Proper installation of snowstores on the roof of a corrugated floor

Choosing the design of the snowstore itself, it is necessary to take into account the fact that it is to the brackets account for the main load. Therefore, these fasteners should be made of durable metal, they should have a fairly large square of contact with a professional flooring, and they must withstand quite serious loads, up to 300 kg per element.

Typically, the installation of brackets falls on the crest of the wave of professional flooring, in fact, it is like installing the ridge on the roof of the corrugated floor. In this case, the fastener should be included in the wooden plane of the roof crate. All models, except for point, are installed in a row in parallel eaves at the level of the carrier wall. Below to install is prohibited. The mount is made by self-drawers every 50-60 cm. Neoprene gaskets (cuffs) are necessarily installed under the screws. It is believed that the fastening step should be no more than the step of the crate.

On steep and large roofs, snow-holders are installed in several rows. The distance between them is 2.5-3.5 m. As for dotted devices, it can not be installed in a row. Chess option is used quite often. The main thing is to evenly distribute fixtures by the roof site.

In the snowy winter, the pitched roofs are a hidden source of danger, because the gathered solid precipitations can collapse in passersby at any moment. To avoid this, snowstores are installed on the roof. The use of the device is extremely necessary if the finish is made of smooth professional flooring. Thanks to snowstanders, hard preciputes remain on the roof surface, and when blending, melting water flows along the waterproof. Let's learn what is this device, about its varieties and we will give the installation instructions.

Snow-roller systems are distinguished by form, sizes, material, as well as reliability of the design. For the roofs of the profiled sheet, structures are used in which the design of pipes, grids or corners are used as a snowfield. Consider every kind in more detail.

Lattble

Lattice snow desuaster

This is the simplest, but at the same time a fairly effective view of snowstaving devices. The universal design consists of brackets that are attached to the roof, and vertical lattices. Such barriers are able to delay even the most minor pieces of ice, which is why the roof can accumulate a large snow mass. Therefore, snowstores of this species are installed only on the roof with a high bearing capacity.

All parts are made of galvanized steel and painted with moisture-resistant paint, so the lattices can be chosen into the tone of the roof. As for the sizes of the grid, they can vary depending on the model, and the synchtercing capacity of the system directly depends on them. The smallest barriers have a height of about 5 cm, and the largest - 20 cm.

Tubular

Tubular sonyaaster

The principle of their work is slightly different from the lattice. In addition to the arrest large number Snow, tubular systems gradually pass it, which reduces the load on the roof. Such snowstores are allowed to be mounted on the roofs of any type and with an inclination angle to 60 °.

It is interesting: on the roofs with a bias over 60 °, these systems are not established - it is believed that the precipitation is not delayed at all.

Like the previous view, tubular structures are made of galvanized steel, followed by applying a colorful layer. As a result, the product is obtained by durable, not subject to corrosion. Color can be selected for any roof. Tubular snow-bags are equipped with two pipes with a diameter of 15 to 30 mm and length from 1 to 3 m, as well as fastening elements and brackets with plates for mounting to the roof. The number of backups depends on the length of the pipe.

Corner

Corner snowstores on the roof of the proflist

This type is considered to be the least successful, since the corner snowstores completely prevent the passage of snow. Therefore, in regions with a significant amount of precipitation, these devices are not applied. This is due to the fact that their height often does not exceed 6 cm. In addition, corner snow-bags are made from metal sheets, commensurate in thickness with a straightened. Therefore, they do not have sufficient strength to desert large snow navalov.

Such products are desirable to use only in regions with low snow cover and install on roofs with a slope of no more than 30 °. At the same time, the latter will have to clean from the snow and accumulated mud.

There is another kind of snowfoot snowfoots from corrugated flooring - these are spot barriers. But these systems appeared relatively recently and arguing about their reliability is too early. However, compared with the angular, the point devices have an advantage in terms of fasteners - their installation involves the compound is not with a doom, but with the roofing metal itself. They hold on the roof only part of the snow. Nevertheless, this is enough to prevent avalanche-like gathering.

Installation features

Installation of each type of synchtercing systems on the roof of the corrugated floor may have some features. For example, the installation of corner products is the easiest and made using self-tapping screws with a rubber washer. Fastening with self-tapping screw is carried out in a wave of profiled flooring. For mounting corner barriers, you can do without enhancing the root, but the fastener element must be tightly cut into the wood. Otherwise, the design will be fragile. Mounting corner snowstores need to be placed through one wave.

As for tubular and lattice systems, their snowstorming elements are installed on the roof using support brackets. The latter are attached as well as corner products - on the self-tapping screw. Both types have around the perimeter of the building, along the skate. They have them in one or more rows.

Installing any of the types of such systems is not a challenge. This work can be performed personally, without the help of a building master. Moving directly to the installation.

Preparation for mounting

Before doing the fastening of snowstores, you need to decide on the type of snowstores and the number of rows. As mentioned earlier, the choice should be done by relying on the intensity of precipitation in your region. It is important to take into account the angle of inclination of the roof on which the barrier is planned to be installed and the presence of fence on the roof.

IMPORTANT: Install the device is above roofing fencing. However, if it is impossible - designs can be combined.

Now proceed to the markup. Measure the perimeter of the roof and we mark the optimal location of the stops. The distance from the last bracket to the edge of the pipe should not exceed 300 mm. The maximum distance between the brackets is 1 100 mm.

Typically, a snowman is installed at a distance of 600 mm from the edge of the cornese swell and in parallel to it. If you need to install another barrier, then it is possible to have it no closer than 2-3 meters from the neighboring.

Tubular snowstores

To work, you will need the following tools:

yardstick;
marker;
set of drills;
drill;
self-tapping screws with rubber pads (usually come complete with the system).

At the end preparatory work You can go to the installation of the system. As an example, consider the installation of tubular snow snowstores, which are considered the most reliable, efficient and enjoy the greatest popularity.

Instructions for fastening on the example of a tubular design

The installation order of tubular snow-holders is as follows:

In accordance with the markup, the support brackets on the self-tapping screw with the perforator.
In the bracket hole insert the pipes of the snowmobile.
To achieve the desired length of the pipes are joined among themselves. This provides a special one-sided crimping. The joint is fixed by a bolted joint.
Similar activities are made on each side of the building, throughout the perimeter.
At the end you need to check the bolted connections reused.

Photowe example a step-by-step installation

Bolted tubes Plant Tubes Installing the support bracket

The procedure for mounting with lattice synthelasts is completely similar to the above. And the installation of corner products is different only in the absence of 2 and 3 points.

Despite the fact that the use of special devices Significantly improves safety and reduces roof wear, do not forget about the need to regular roof cleaning. This will reduce the burden on building structures and will extend their service life.

In the snow regions of the country there are threats to the rapid dumping of a snow layer with roofs of buildings, which almost always carries with them not only the destruction of various designs, but also the death of passers-by. But such a problem has a very simple solution - snowstores on the roof.

These structures with ease hold the entire thickness of the bulk of the snow on the roofing surface. And the snow comes out only in the form of melt water along the drainage system.

Snowbornels have several species, and they are calculated from the tilt of the skate, roofing, the number of snow on the area in the winter period.

Categories and species

Any kinds of snow-setpoints for the roof, often can be found in the roofing material store, but in the case of its absence, it can be purchased separately and after the construction of the roof.

Please note that when you come to different construction stores, the snowmobiles for the roof may differ in the title, for example, in one this will be snow-gluable fences, and in other snowballs, snowts or snow-sneakers. By the way it is worth noting that the different name is not the only one distinctive trait All these devices. They possess various buildings, and, therefore, and they will have different functions.

These protective devices have two varieties, one of them perform the lock function, while others cut the snowballs.

Snow-blocking elements or differently snow-boarar. Such elements of the roof, as a rule, serve only for retention of snow and over time it is removed in a natural way, i.e. melting. Manufacturers ensure that even partially snow leave the roof limits not in a state, however, the practice confirms this

To the second category can be attributed snow-Pieces. They are designed to cut a solid layer of snow into small parts. This avoids the fall of massive snowballs to the ground, therefore, damage will not follow

Snowmaders on the roof have a variety of structure, and the dimensions of each of them also differ as the metal from which they consist.

Therefore, the stronger the material will be, the biggest masses of the snow it will be withstanding, it is for this that it is worth paying attention to their choice.

Tubular snowfoot

Tubular snowstanders on the roof have the structure of two pipes that are kept on the brackets. The diameter of pipes, as a rule, is 15-30 mm. The entire design in the height will be about 15 cm. The bracket is called a vertical plate with holes located at a certain distance, they serve to support pipes.

The lower horizontal shelf serves as an element of fastening to the roof. As the fasteners, as a rule, hexagon screws for cut-in to metal with an 8x60mm size are used. With different roofing coatings, the form of the bracket and its mounting methods will differ.

A tubular type of snow-shrew cells the distance between the bottom pipe and the roofing coating will set the strength of the entire design. The most optimal value is in the range of 2-3cm from the roofing coating to the nearest pipe, and between them 10cm.

Tip: Tubular snowstores for roofing should be arranged on the rods where the angle of the slope does not exceed 60 o. It is inappropriate because with a large slope of the Snow mass itself will go down and it will happen quite often, but after 60 it does not make sense after 60. On such sharp roofs, he is not able to lie down.

Tubular snow-planes can be attributed to the category that cuts the layers of snow without any problems. Such constructions, in general, are considered the most proven and reliable, they will easily withstand the high pressure of the snow cover, and their installation can be made on any roof.

No matter, these materials will be in the form of sheets rolled into a roll or metal tile. The installation occurs around the perimeter of the building, along the most important skates.

It is worth noting that tubular snow-planes are mounted with a solid side, but it is not worth doing this into disperse. In areas where snow sediments are stronger, it is not rare to see snow-set kernels installed in two rows, which are in 2-3 meters from each other.

Fastening the lower rows of the tubular type of snow-workers is made above the most stable - carrier wall, 40-50cm from the sink of the cornice.

For proper selection Color range of data elements You will not notice fasteners and even the design itself. As a rule, tubular structures are made in the form of galvanized steel coated polymer coating or paint. Consequently, the material is durable and corrosion-resistant.

Snove holders of lattice type

These elements have a fairly wide selection of sizes and design. The lattice snowstores are ideal for the roof from the proflist. They have an uncomplicated design. It includes brackets and grille itself. Elements of this system are galvanized and painted, which is good corrosion protection..

By the way, the wealth of paints allows them to choose them almost to any tone of roofing.

I said that dimensions and designs could be different, but it only concerns the lattice, the brackets are alone for everyone.

Their height is in the range of 5-20 cm. Consequently, the larger the area of \u200b\u200bthe grid, the greater the snow layer it can withstand. For example, the largest size with ease withstands the most written as possible in the characteristics of the layer of snow cover to the ice. Despite this, there are cases when the snow is too much, so obstacle to some caution.

Such a kind of snowstanders is often found on sharp roofs, it allows you for sure to protect yourself from the fall of solid snow. The effectiveness of their work directly lies on the quality of the lattice. You should not worry if your roof is some kind of unique, ask how to fasten the construction stores for your type of roof.

IMPORTANT: If very large snowsets are observed in your region, the installation of tubular snowstores on the roof will be safer for you. The fact is that the lattice under very large weights can be fed, which will not be safe. By the way, acquiring protective elements for the roof, do not skimp and pick up qualitative materials, do not even look at cock and cheap products, because you pay for your safety.

Inventive masters can advise another option if you have already acquired lattice snowstores, but you are not sure about their reliability, you may be offered to combine the grille and pipes. In such a design, you can accurately be sure.

The installation process itself occurs in a row along the entire length of the skate, but if its length is more than 6 meters, then you will have to install additional protection, for example, corner snow-roofing sneakers.

Corner snowstorms

This type of protection against snow cover rolling is to arrange the tenants of not very northern regions, in general, where there is little precipitation. The installation of corner snowstores will be maximally appropriate for the roof of the corrugated floor and the metal tile, because Materials, color and characteristics of protection elements coincide with roofing.

Corner snowstores on the roof are sometimes called lamellar, but if you look at the photo, you can make sure that it is not exactly suitable for them.

The element itself consists of some size of a metal sheet bent into the design in the form of a triangle. It possesses two faces, one of which is emphasis, and the other takes all the pressure on itself. Thanks to the shelves, the mount is performed very firmly. Height of the entire element 4-6cm. As a rule, corner snowstores on the roof are arranged on the slopes of the slope of not more than 30 o, because he simply cannot withstand a large pressure.

Easy installation is pretty positive quality. Fasteners are made directly to the roofing material itself. By the way, if your roof is made of wavy elements, the fasteners should be produced to the protruding waves.

They, as a rule, are arranged along the entire length of the sink in a chess and have several rows. Their number can be any, but note that the distance between them should be in the range of 0.5-1m.

As an output, I can say that such snowstores on the roof are very easy to install with their own hands, but it is worth it only in the regions where little snow. And if the snow falls quite a lot, then you will have to take care more about cleaning snow cover.

Articles and videos on how to make corner snaggers on the roof with their own hands can be found on the Internet and at the bottom of our conversation. It is acceptable only in the case when you want to save, but consider, with the wrong design, you are dangerous not only yourself, but also your loved ones.

Bugeli.

It is unlikely that you can call the bohels with full-fledged exercises. They are used only as a supplement to the main protection, or on the roof of soft materials with a small bias. This is done naturally as reinsurance, because this is how the likelihood of a snow mass with a small slope is extremely small. After all, it is like soft materials that, as a rule, there is a sprinkler, which will not allow the snow to slide, but if you are safety above all sorts of beliefs, and you do not want to spend money on full protection, then your choice.

They are arranged at a distance of 50-70 cm from each element. It is worth noting that you will not be able to install Boheli if you have already completed the installation of the roof. The fact is that their mount is made to the crate, and she, as you know, is under roofing material. Such a cunning allows you to be sure that the roof will not flow in the places of fastening.

Log-speaker

How is such a snow sneakener installed on the roof? The log as protection is used very rarely, but still it takes place. Most suitable for creative people who have a roofing completely made of wood (trick or duncan).

Logs are stacked on special hooks, and they, in turn, are attached to the crate or sling feet. Well, and how do you understand - here the size is important, i.e. The larger the log you save, the more snow it can delay.

IMPORTANT: when such a snow-resistant device should take care of the gap between the roof and the log itself. It should be 2-3 cm. This will provide a unobstructed stack of melt water.

Nuances of installation of exercises

Installation of speakers, like other work in construction, is better to combine into one process and produce it immediately. For example, if you are running the roof, then take care of the device of the protection elements immediately, and not after a while. This will serve as a greater guarantee, because with time the roofing materials wear out and after a while they will not be able to withstand the masses of the snow, which is collecting snowfoot.

As saving not only money, but also time you can arrange stops only in the necessary places. For example, over paths, parking, balconies, etc.

Please note that the radius of the fall of a snowball with a roof, which has a bias of more than 35 o, can be 1.5m and falling it will hardly be smoothly down.

IMPORTANT: To make the fastening of consumer holders on the very sink of the roof is prohibited. The defense should be at a distance of 80cm from the edge. The pressure that is created by the snowy mass is very large for the eaves and simply will break it.

The price range to these protection elements is very large and can be from 2 to 250 dollars. It all depends on the brand, size and material.

Metal tile. Types of snakers and their installation

When you know some nuances of mounting, you can proceed directly to the process itself and begin with metal tiles.

Metal tile is a very common material from developers, it has the most better qualities And price than other roofing coatings, so people choose it.

The smooth surface of the roofing sheets allows the snow to be easily moved when he swallows, therefore, snow-settresters are mandatory.

For this type of roof, the most suitable are:

Tubular
Grident
Corner

The latter, as mentioned above it is worth applying only when the bias of the roof is not big, and the precipitates in your region are insignificant.

Now let's consider the installation process itself, and you will understand how to fix the costumes on the roof of the metal tile.

Some markups are performed, where protection will be
The shap is strengthened with an additional bar
The entire set of snowfoot is assembled on Earth, but the fasteners are left in a relaxed state.
Nastilka is made roofing materialand then drill holes for the device brackets. If you have a wave material, then the mount is made to a concave wave. The whole process is made by 8x60mm bolts. All created holes should be sealed with rubber or silicone linings. The bias of the roof and its length will affect the step of the brackets. For example, if the conditions are the toughest, then the distances in 50cm between them will be more than enough
If it is tubular snowstore, then we insert pipes into the grooves, and if the lattice, then we simply connect everything together and clamp the fasteners

IMPORTANT: All security elements should be under the carrier walls. If the building is present mansard Floor, then above its window, be sure to enhance the crate.

The length of the skate more than 6m implies a device of an additional series of stops.

The design of the brackets may vary depending on the roofing coating. For example, if your metal tile is the production of "Monterrey", you will have to use brackets with special protrusions. Such additional element Removes the need to strengthen the crate.

Profile as a base for snowfoot

The professional flooring is almost different from the metal tile, therefore, the snow will also easily slide down and fall. The most intense it happens when the snow fell a little. By the way, the resulting ice on this roofing material is very harmful to him. With avalanche, the coating is scratched with an avalanche, corrosion appears, and the service life decreases at times. In this regard, snow feet for the roof of the corrugated floor protective function both residents and coating itself.

Types of snowfoot for professional flooring are similar to the types of metal tiles, they are also three, but it is more likely to install tubular with galvanized, painted under color gamut Roof.

How to take into account all the nuances and correctly install snowstanders on the roof from the professional flooring? Yes, it's very simple, it is worth only to remember some rules.

The whole process of fixing device is carried out in the roofing itself
Strengthening the crate necessarily
Drilled holes to expose sealing
Fastening is made in the bottom wave of the proflist, in order not to conquer the material

The device of snowfoot for already ready-made roofs is a somewhat difficult occupation, because you have to take off the coating first, to strengthen the crate, and then lay it again, but if your master who made the installation of the crate, takes care of it, then unnecessary work can be avoided. And also advise, what snowstores on your roof are more suitable and how to install them correctly.

If you mount protection as reinsurance, then choose corner stops. After all, the enhancement of the crates is not required, and they cut into the leaf of the professional flooring. It removes the need to pale a roof, but provided if you get a bolt into the crate. Fastening B. wooden design Allows you to stop strength and withstand higher loads. As a rule, they are placed through one wave.

Device of extinguishers on a roof

Folding roofs provide only a device of tubular or lattice stops. Their installation is somewhat different, but only by the fact that the first brackets of a unique form suitable only to them, and their fasteners are made only to False itself. Due to this, the sealing of roofing remains not touched.

The installation process is very simple, so the question is how to put snow-sauers on the roof from the fold and is not a question at all. For this you need only:

Put a clamp to Falk
Drill in advance marked places 2-3 holes
Insert bolts in them and clamp nuts

It is worth remembering that the step of fasteners depends on the downhone roof, but the most reliable option will be the connection with each fold.

The biggest advantage of the folding coating can be considered that there is no need to strengthen the crate. The entire process of mounting snow-holders is made on top of this roofing. Ultimately, the whole design is obtained quite stable and has a pleasant appearance.

By the way, for this type of material there are copper patterns of snowfoot, but you will not find them a set, you will have to acquire everything separately and then collect yourself. But if you lower this nuance and remember that copper is more durable than even galvanized metal and the life of its operation can reach 150 years, then this is a trifle.

Snowflowers on a soft roof

The soft roof is very different from the metallic and has a number of its features that affect the choice of a speaker.

Exceeding slope of the skate soft roofs More than 15 o no permissible, therefore, and the likelihood of falling snow from it in large quantities will be extremely small. Therefore, there is no need to acquire the most strong stops
The stone crumb used as a sprinkling on the soft roofing material may be at all a sufficient factor to ensure your safety. After all, it is she who does not allow the snow mass sliding down
Strengthening the cage is not required, since when installing flat roofs she is so reinforced

If you still gathered to arrange a snow-softener on the roof of soft materials, then it's worth it when laying roofing material, and not on a functioning roof.

I can only say that the bohegeel device will be quite sufficient to ensure safety, and the pipes are not only expensive to you, but will be inexpedient.

The location of triangular stoppers must be made in accordance with some nuances:

Rows are created in a checker order. They should be two or three, and the distance between the elements is 50-70cm
The soft material must overlap the connection site of the bougiel and the crates, but not close it
Fastening elements are ordinary self-tapping screws

If your roof is already ready, and you just started the bougiel device now, you can safely mount them from above, but use special rubber gaskets.

As you understood from this article, it is not difficult to establish snow designers on the roof, but allows you to protect yourself and save the roof safe and safety. If you do not understand something, or you want to consider some nuances in more detail. You can watch the video where it is described how to install snowstanders on the roof.

The roofs having a slope even with a slight bias are very popular, as snow is practically delayed. But too steeply skate can cause a natural disaster in the form of a snowy mass gathering, which is the threat of life and health of people passing by.

Snow protection

In most cases, snow clenches with smooth surfaces. To prevent such phenomena, snow-holders are installed on professional flooring. These devices can be made with their own hands, but for this you need to know how to install them, and which additional measures Accepted for snowstand.

Appointment device

In some regions of Russia, the winter lasts up to 9 months, at this time you can observe not only strong frosts, but abundant snowfall. The accumulation of snow has a significant burden on the structure and the base under it, so the buildings most often have a roof with a slope of more than 35 degrees.

Smooth roofing materials having a slippery surface do not give the snow to linger on the roof. In addition, there is a stream from the premises warm airwhich to some extent heats the roof. As a result, the formation of ice crust is observed on the surface.

The installation of snowstanders on the roof of the professional flooring helps homeowners solve the following problems:

Snow mass delay on the roof of the corrugated to the moment of melting under the influence of sunlight. Tala water is sent to drainage system and in storm sewer.
Snow cap, passing through the snowmobiles on the roof of the corrugated floor, is cut into thin layers. In this form, the snow represents a smaller threat to passersby.
Snowplowed on the roof of the corrugated floor does not allow heavy snowy mass to sculpt in the drain and deform it.
The resulting ice crust when sliding can leave scratches on the surface. In these places under the influence of water, corrosion foci are formed, prematurely destroy the roofing material.

Methods of snowstand on the roof of the corrugated

With an independent device of a snowmobile for a roof from a corrugated floor, it is necessary to select the elements of the same color with the roofing material. Most manufacturers offer snowstand elements complete with professional flooring.

To understand how to install snowstanders on a roof from a corrugated floor, you should know that all elements are divided into two groups depending on the principle of operation:

Snow-Barrier. This element is set to stop the snowy avalanche to a complete melting under the sunlight. However, the accumulation of snow mass has a significant burden on stropile design Roofs and base at home. This property may well be considered a lack of snow-melon. It is possible to solve the problem with regular removal of a large snow accumulation manually.
Snow-Piece. These elements restrain the snow cap, but short time. Under the pressure of its own mass, the layers of snow pass through the snowmates and roll in small portions. Such a design does not waste the roof, but does not protect the territory around the house from the snow.

Using professional flooring as roofing material, it is worth thinking about installing snow-settresters to metal products to prevent the departure of a large snowy mass. Neglecting these elements can harm the health of households, damage the roofing material and reduce its service life.

Varieties of snowstores

Installation of snowstanders on professional flooring involves performing actions to create a solid barrier, which is capable of not only to stop the snow cap, but also to hold it for a while. Depending on the volume of precipitation, the slope of the roof rope and roofing material is selected view of the snowmobile and the required number of elements.

On the roofs of the corrugated floor, several types of elements for detention for snow mass are used:

Grid. These elements have a height of about 20 cm, their mount is performed using brackets throughout the slope. The grilles are able to hold on the roof of large snow caps, so it is possible to install elements of this type with your own hands only if slinge system It has a high bearing capacity.
Plates. Such snowstand elements are a perforated metal plate, fixed on the roof through the corners along the back of the edge indented by 40-60 cm. This allows the design to hold a high snow mass firmly. Plastic snowstores on the roof of the corrugated floor are characterized by lower cost and easy installation, but it is recommended to use them when the slope is not more than 30 degrees.
Tubes. Elements of this type work on another principle than previous models. They are designed not to hold snow, but for its cutting. Snow cap, passing through the tubular elements, is divided into thinner plates. The design of this type is two parallel tubes inserted into the holes of the brackets. Due to the fact that the snow mass is not delayed by tubular elements on the surface of the roof, and goes on the ground with small pieces, such devices are considered the most effective for the roofs of the corrugated floor.

Installation and installation on a professional owl

The installation of snowstand elements on the roof from the professional flooring requires an attentive attitude to work. When fixing, there is a disruption of the integrity of the roofing material with fasteners, so it is best to use special roofing self-taverns with a rubber hat and a seal.

In general, the installation of snow holders implies the following actions:

The location of the elements is determined. The installation of the first row should be performed along the sweep over the bearing wall of the building. At this level stretch the thread or cord.
The estimated load on each element is about 200 kg, so placing the brackets are necessary at a distance of 50-60 cm. Roofing screws are used for fastening.
Inserts of the brackets insert the pipes of the snowmobile. If the installation of the second row is planned, then it is installed after 1.5-2 meters.

A large load is assumed to any snowmobile element, therefore, for their manufacture, it is necessary to use high quality materials only. The fixation of the brackets is recommended to perform three screws. It should be remembered that a negligible element may not withstand a large snowy mass. This will lead to the breakdown of brackets and the subsequent deformation of the roofing material.

On the recommendation of the experimental roofers on the roofs having a bias of more than 60 degrees, the tubular snowstores should be installed for professional flooring. Sometimes you can use the combined elements in the form of a grid, welded to the pipes of a snowmobile. To save, you can make such a design yourself.

In particular snowy winter, the roofing structures act as hidden sources of danger, because if solid precipitates are harvested on the surface of the roof, they can hit down to any second. In order to exclude such a probability, snow-setkers are mounted on the roof. The use of such devices is necessary if the finish is made of a smooth profile sheet. Due to the presence of snowstanders, the snow remains on the surface of the roof, and when warming flows along the waterproofs, turning into melting water.

Choosing a snowmotter before starting

Before you are carried out on the roof of the corrugated floor, it is necessary to understand the main varieties of these structures. Snow-boarders can have different sizes, have a certain reliability and material based.

For roofs from the professional sheet, systems are used, which are most often made from corners, lattices and pipes. The second option is the easiest, but effective. The design is a universal system from the roofing brackets. With the help of such barriers, it is possible to resolve the question of detention of minor pieces of ice, because of which a large mass of snow is accumulated on the roof. That is why these designs are installed on the roof with an impressive bearing capacity.

Such parts are made of galvanized steel, which is stained with moisture-resistant paint. Therefore, the symbulator system can be selected by taking into account the color of the roof. If we are talking about sizes, they may vary depending on the model, while the ability to delay the snow will depend on the dimensions. The smallest snowstores can be limited to a height in the range of 5 cm, while the largest height is up to 20 cm.

Features of tubular snowstand systems

Before installing snowstores on the roof of the corrugation, it is necessary to understand the main varieties of such systems, among them and tubular snowstores. They are able to hold a large volume of snow, passing it gradually, which reduces the load on the surface of the material. Such snowstores can be installed on any roofing, the angle of inclination of which does not exceed 60 °. If the slope is higher, the tubular systems are not installed, since it is ineffective in operation.

Such structures are also made of galvanized steel, and paintwork is applied to them. As a result, the product is gaining durability and are not subject to corrosion. Such snowballs are complemented by two tubes, the diameter of which can vary in the range from 15 to 30 mm, while the length can vary from 1 to 3 m. There are fastening brackets and elements with plates for fixing on the surface of the roof.

When it is worth choosing corner snowstanders

Before you the installation of snowstanders on the roof of the corrugation, you should pay attention to the corner species of such systems. It is worth recognizing that such structures are the most unsuccessful, because completely prevents the passage of solid precipitation.

Therefore, if the house is installed in the region with significant quantities, then such devices are not used. This is explained by the fact that their height is usually not more than 6 cm. In addition, such snowballs are made of sheet metal, the thickness of which is commensurate with a thick sheet thickness. For this reason, these systems do not differ in high strength to detention a large volume of snow. It is recommended to use products in those regions where snow covers are quite low, and the roof slope does not exceed 30 °. At the same time, from time to time it will have to be brushed from accumulated dirt and snow.

Installation

Installing snowstanders on may differ technology when using a specific type of design. Thus, the installation of corner products is the most simple, and you can carry out work with the help of self-tapping screws with a rubber washer. The fixation is made in the wave of the proflist, which is most efficient.

You can do the installation of corner snowstores without carrying out the lattice enhancement, but the fastener should be tightly embedded in wood. If you do not consider this rule, the design will have low strength. Corner snowstores are installed in such a way that the fastener is located through one wave.

Features of the installation of lattice and tubular systems

Installation on the roof of the corrugated, as well as lattice systems, is carried out using support brackets. They must be fixed as corner products using self-tapping screws. These types of snowstands are installed around the perimeter of the construction, it is necessary to arrange them along the skate. Systems can be located in one or more rows.

Preparatory work

Before starting work on the installation, it is necessary to determine what kind of snowmobile supporters will be used, as well as how many rows do you plan to mount. At the same time, it is important to take into account the intensity of precipitation in a specific region. It is necessary to take into account the angle of inclination of the roof, as well as the presence of fences on its surface. You can independently have the installation of snow soverees on the roof. The surface of the surface will assume the presence of these systems that should be placed above if such takes place. Whereas in the absence of such a possibility of design can be combined.

At the next stage, you can start a markup, for this it is determined by the perimeter, as well as places for the location of the stops. The step from the last bracket to the edge of the pipe should not be more than 300 mm. The maximum distance between the brackets is 1100 mm. As a rule, snowstores are distinguished from the edge of the cornice of 600 mm, located in parallel to him. If you need another barrier, it should be placed not closer than 3 meters from the neighboring.

Preparation of instruments

The installation of snowstores on the roof of the cornet, the instructions for which the article mention is mentioned in the article, implies the need to have certain tools among them:

drill;
marker;
yardstick;
set of drills;
saws.

Choosing fasteners, it is necessary to prefer the one that has rubber pads, usually they are supplied with the system. After the preparatory work is completed, it is possible to start the installation, as an example, the technology for the installation of a tubular system, which is the most efficient and reliable.

Installation instructions

Setting snowstores to well can be carried out. For mounting work In accordance with the markup, you must install the support brackets using a perforator and screws. The pipes are installed in the holes of the bracket, and to achieve the desired length you can dock them with each other. For this, the manufacturer provides one-sided crimping.

The resulting junction should be strengthened by a bolted compound. The same actions should be carried out on each side of the building, moving around the perimeter. At the final stage, the master should be checked for strength.

Nuances of work

The installation of snow-sowers on the roof involves using a riveter instead of a screwdriver if the latter was not available. When it is necessary to work with snowstore models, the length of which begins from 70 cm, then two screws will not be enough. At the same time it is necessary to break the additional holes in the center. By purchasing a trap, you should consider it to understand whether the manufacturer identifies the places on them where you need to work with screws or rivets. In the first case, we are talking about short snowmaders. If no designations, it is necessary to retreat 3 cm from the edge and break through the hole.

Conclusion

The scheme of the installation of snowstanders on the roof of the corrugated floor was described above. If you want to understand in more detail for which technology and in what places the roofs to set the stops, then you need to consider the photos that are presented in the article.