Scissors for metal Cricket nozzle on a drill. Nozzle on a drill for cutting metal - mechanize a difficult operation. What does the quality of the cut depends on

You can not always find foliage finishing material required size and shape. During repair, installation of fencing from the profiled metal sheet, devices roofing It is required to quickly cut one or another workpiece, adjust the standard element for actual dimensions. For cutting, you can use the corner grinding machine, scissors, others. cutting tool. If it is not at hand or are you limited in means, that is, an alternative - nozzle on the drill cricket.

Short description

This is a removable mechanism that is installed on the standard electric hand drill cartridge. It is designed to cut flat and corrugated metal sheets:

  • Composite aluminum sheet thick up to 2 millimeters
  • Galvanized profiled sheet thick up to 0.8 mm
  • Copper, brass thick up to 1.5 mm

By appearance The nozzle on the drill cricket resembles a steel cylindrical blank, with "fingers" sticking in both directions. The cylindrical dwarf is the body through which the torque is transmitted from the drill into two cutting surfaces. "Fingers" are paired matrices in contacting directly with a metal blank. Included with the tool there is a plastic threaded handle holder, which is winding on one of the paired cutting surfaces.

In addition, the nozzle comes with a spare matrix and punch, as well as a hex key.




Principle of operation

The nozzle on the drill cricket does not saw the metal as an angular grinding machine, but cuts it at the expense of frequent translational movements of the matrix. The working unit converts the torque from the rotor drill. The tool cannot work on low revs. To obtain a quality cut, it must maintain the speed of rotation of 2700-3000 rpm. If this parameter is not performed, the metal around the slice is short, the quality of the finished product is deteriorating.

Application area

Nozzle is widely used for cutting of thin metal. Its design is specifically designed to perform both rectilinear and curvilinear cuts. Possessing a certain skill of work, you can perform a figure sawmill for a complex trajectory.

Unlike an angular grinding machine or scissors for metal, "Cricket" is capable of cutting from the center of the workpiece without creating through propyl.

The nozzle for cutting is especially in demand for roofing work and installation of fences. The thing is in the material. The profiled sheet is mainly used, which is perfectly cut using this tool.




Positive properties

The nozzle on the drill cricket is widespread due to a number of positive properties. It wins on its operational characteristics in some power tools.

  • Mobility. She has a small size, much less than the Bulgarian. The nozzle is easily installed and removed from the drill, which makes it easier
  • High performance indicator. Cricket has two full-fledged cutting matrices. If one fails, you can use the other. In addition, complete with the tool comes the third spare
  • Maintainability. There are no complex mechanisms in its design, there is almost nothing to break. The cutting part comes with a finished block that is easily installed on the spot
  • Speed \u200b\u200bof work. Numerous tests show that the performance of work and the rate of sawing in the nozzle, significantly exceeds similar operations of the corner grinding machine. Scissors for metal do not go to comparison at all
  • The quality of cut. There are no competitors for this indicator at the dragonfly. Due to the translational movements of the matrix, the metal edge in the cutting area remains smooth. There are no burrs on it. Metal does not heat up, protective polymer coating Profiled sheet does not burn. Zinc protection is not destroyed. While in the process of sawing, the leaf is charred, burrs remain on them
  • No side destruction. Working with the Bulgarian is associated with the formation of sparks that scatter at a considerable distance. If a galvanized profiled sheet is processed, the sparks burn the protective coating. In the process of operation, the metal will cover brown pins of rust. The sawing by the nozzle "Dragonfly" passes with the complete absence of sparks. Rust problems do not arise
  • Ergonomic. Handle - holder makes work with a tool comfortable and safe

Negative properties

They are not so much, they do not have a critical impact on the choice of tools:

  • The limit associated with the type of grip. He is just two hands. Therefore, it is impossible to carry out operations on inclined planes, where it is necessary to hold
  • Metal thickness. The nozzle is designed for cutting thin metal

Rules of Safe Work

Practically do not differ from standard measures when working with a sawing tool:

  1. It is prohibited to saw, keeping the tool with one hand. This can lead to his rebound;
  2. Before starting work, the rigidity of the holder handle fastening is checked. To do this, it turns clockwise to the failure
  3. It is permitted only in protective glasses and mittens;
  4. It is recommended to cut a sheet from yourself, and not to yourself;
  5. It is forbidden to work with a faulty tool. These include: a breakdown cartridge for a drill, a wastewater sawing matrix, stressed handle holder

Firms - manufacturers

Products of different brands are similar to each other. The main difference in the thickness of the sheet, which can sow a specific model. The price directly depends on this.

The Russian market presents several firms that are worthwhile:

  • Eckor
  • Corvette
  • Sparky.

The use of scissors on the drill makes a significantly easy to perform roofing, installation of a metal fence, other manipulations with sheet material. A comfortable combination with a hand drill makes it possible to reduce the cost of buying an expensive specialized tool. Ready product It turns out neat and high quality.

If there is a need for cutting metal, and the grinders or hacksaws are not available, the electric drill with a special nozzle can be used for this purpose. Such devices allow separating sheet steel segment, and some models allow working with a metal profile.

These fixtures have not only a large number of Advantages, but also restrictions, the main of which is the thickness of the material with which you can work.

Advantages of drill nozzles

The use of such a snap can be not only in the absence of an alternative way to treat the material, but also in the case when the heating of the metal sheet is undesirable.

Among the main advantages of using nozzles on the drill, before using the Bulgarian, the following can be allocated:

  1. Higher quality cutting surface.
  2. The device allows you to make a hole in the metal of any form.
  3. Significant cash savings, due to the lack of spending on consumables.
  4. The tool is very easy to use.
  5. Many nozzles allow you to work with both metals and plastic sheets of the corresponding thickness.
  6. When using a drill equipped with a battery, cutting can be made in places where there is no possibility to connect to the home electrical network voltage 220 V.
  7. The ability to combine several functions in one device at once. If there is no need to cut a thicker metal, the drill can be used to drill holes and for cutting the metal sheet.
  8. Small weight of fixture.

Listed the main advantages of this product in front of other types of metal cutting. Models of such nozzles can differ significantly in many respects, including at cost.

Scissors

The nozzle scissors on a metal cutting drill is a device that converts rotation of the cartridge drill into reciprocating movements, which, thanks to the special matrix, knock out a strip with a thickness of 3.1 mm in the metal.

With this method of separation, the slice is obtained even and high quality, which allows you to almost completely abandon the additional processing of the material in the future.

A peculiar scissors can be cut metal whose thickness is not more:

  • 2 mm - when processing aluminum.
  • 0.8 mm - if you need to cut off the stainless steel.
  • 1.5 mm - for processing copper and brass.

This nozzle on the metal cutting drill will allow to carry out the material separation, only if the tool electric motor develops at least 2700 rpm.

"Cricket"

The "Cricket" nozzle is a universal device, with which you can perform a separation of not only metal, but also of various plastics. The advantage of this pribluda is to be cutting both sheets and profile material.

Through the use of two cutting heads, the cut is performed perfectly evenly requiring additional processing after the cutting is completed.

Using the device of this type, you can process the material of the following thickness:

  • Aluminum - up to 2 mm.
  • Steel - up to 1.5 mm.
  • Plastic - up to 2 mm.
  • Stainless steel - up to 1.2 mm.

In order for the design to serve as long as possible, and the metal chuck or other material was as even as possible, the manufacturer recommends using this device when the engine turnover drills from 1500 to 3000 rpm.

"Beaver"

Nozzle "Beaver" works on the same principle as the above models. Using it, it can be performed both straight cuts and curvilinear with a minimum radius of 1.2 cm.

Beaver has a little best characteristics For cutting sheet metal, for example:

  • Steel - up to 1.8 mm.
  • Stainless steel - up to 1.3 mm.
  • Aluminum - up to 2 mm.

Price of popular devices

Quality tools can not be cheap. For cutting metal, adaptations must be made of a material that undergoing constant loads is not deformed. Among the variety of both domestic and foreign manufacturers should be distinguished the products of the following brands:

1. NP 1.8 Sparky 181874 nozzle - the device is made in Bulgaria and is distinguished by high quality and acceptable price.

The device allows both linear cuts and radial, and the edge quality will be highest regardless of the type of material that must be separated. Sparky 181874 can be used as a nozzle on a drill for cutting metal tile, which will significantly speed up the process of building the roof.

The price on the Russian market is about 2,000 rubles, but this cost is fully justified, since the SPARKY drill device is a high-quality product that will serve for a long time.

2. Enkore 14209 - Cricket type Priblud, russian production.

The device allows you to perform high-quality cutting of leaf aluminum thickness up to 2 mm. Indispensable when working with roofing metal materials, since, unlike the bulgol, the metal does not heat up.

The thing can be purchased for 1900 rubles in any specialized store.

3. "Steel beaver" - made in Russia and allows you to work with different metals.

With the help of the "steel beaper" you can easily cut off a piece of aluminum, while the edges will be completely intact. Restriction on the maximum thickness of the metal, in which case is 2 mm.

The device can be used for cutting stainless steel. In this case, so as not to overload the tool, it is not recommended to use a sheet, a thickness of more than 1.2 mm. The cost of pribluda is about 1600 rubles.

4. EDMA NIBBLEX - perfectly copes with a separation of sheet and profile material with a thickness of up to 1.2 mm. Aluminum sheet can be processed up to 1.5 mm thick.

For effective work of the nozzle, the manufacturer recommended the optimal frequency of rotation of the drill of 3,000 rpm.

The estimated cost of EDMA Nibblex in the Russian market - 5,000 rubles. The high quality of the device is confirmed by numerous tests of both professional craftsmen and simple peoplewho acquire the device for home use.

5. Malco Turboshear TS1 - can be used with a drill and for installation on screwdriver.

The device is the most expensive of professional devices and costs the Russian buyer at 7,000 rubles. The nozzle is worth such money, as it is produced in the USA, where the quality control is significantly higher than in China.

  1. If the cutting is used for the first time, it is recommended before proceeding to the main work, make several cuts on unnecessary metal fragments to understand the basic principle of the device operation and avoid errors in the subsequent.
  2. When working with a metal cutting device to get a smooth section of the desired form, it is recommended to keep the drill in both hands during the work.
  3. Nozzles for the drill of Russian production are practically not inferior in quality to foreign analogues, while the price can differ significantly in a smaller side.
  4. It is not recommended to purchase devices from the hands, you can buy a defective product for considerable money.
  5. Store tools follow in rooms where the likelihood of metal oxidation will be excluded due to high humidity.
  6. The use of special nozzles is always justified when carrying out roofing work, so such a device should be purchased even if the scope of work with metal tile is not great.
(1 ratings, Average: 5.00 out of 5) Loading ...

plavitmetall.ru.

Metal drill nozzles: description and varieties, advantages, main characteristics

Engaged in building or repair workAlmost everyone faces the need to cut any workpiece from the metal. To perform this procedure, you can use the grinder, cutter, manual scissors on metal.

But what to do if you need to cut a metal sheet, but there are no such tools at hand? You can solve the problem with the help of an ordinary drill and a special nozzle, which can be bought in any construction store.

What is nozzles for metal cutting

Such an adaptation, in fact, is a pinton or punch, which pierces metal with a plurality of repeated movements with a matrix. As a result of this in the cut metal details A strip of the desired shape and a width of 3.1 mm is formed.

Thanks to the point exposure to the metal, the integrity of the protective layers of the product is maintained as much as possible.

With the help of the nozzle, you can handle the material that has a thickness:

  • aluminum - up to 2 mm;
  • copper, brass, sheet iron, pure zinc and steel having a coating of zinc - up to 1.5 mm;
  • stainless steel - up to 0.8 mm.

The cutting tool leads the drill cartridge to which it is fixed. It is worth noting that cutting the metal of the nozzle can only if the number of turns of the drill will not be 2700 rpm.

Advantages of nozzles

Compared to the grinder, the nozzle on the drill has a large number of advantages.

However, despite all the advantages of the instrument to ensure high quality cutting, a certain skill and skills are needed to work with it.

Special nozzle "Cricket" on a drill for cutting metal

Building stores offer several types of devices on a drill for cutting metal.

Nozzle "Cricket". Device "Cricket" is the vigorous (cutting) scissors, which are capable of performing a smooth slice. The tool is used to cut not only smooth, but also profile metal sheets.

In addition to metal, they can cut plastic and polycarbonate. Used cricket for cutting thin-leaf products:

  • The maximum thickness of the sheet steel must be 1.5 mm.
  • Maximum thickness of the stainless steel - 1.2 mm.
  • Maximum thickness of copper and aluminum - 2 mm.
  • Plastic thickness - 2 mm.

With the help of nozzles, cricket can be cut on horizontal and vertical surfaces, as well as perform internal cuts. So that the inner cut is high-quality, the workpiece must be drilled.

The tool is indispensable when performing roofing, during which the processing of metal tile or professional flooring is required. After applying cricket, the materials used will not be deformed, and the cut will be smooth and beautiful.

If there is a need to make an artistic cutting or drill a large round hole in a sheet, then the "Cricket" nozzle is easy to cope with such a task.

Nozzle "Steel Bobur"

The device is intended for cutting flat and profile sheets (professional flooring, metal tile). It has a cutting mechanism, the work of which is similar to the processing of materials by cut-down scissors.

In the process of metal processing using the "Steel Bobur" tool, sparks are not formed and the protective layer of the metal coating is not burned.

Main characteristics:

  • cut is made at the speed of rotation of the drill at 1500-3 thousand rpm;
  • the maximum thickness of the aluminum and copper sheet should be 2 mm;
  • stainless steel sheets must have a thickness of no more than 1.2 mm;
  • the maximum thickness of the steel sheet can be up to 1.8 mm;
  • changing the direction and corner of the cut - 360 degrees;
  • the minimum reserve radius is 12 mm.

Models of nozzles for a drill and their use

Special nozzles on a drill can be performed both straight and curvilinear cuts. Make curry cuts for installing gutters drainage system or ventilation parts roofing, cut in a vertical and horizontal direction.

After applying the tool, the slice is accurate. Nozzle does not require adjustment and easy to maintain.

In the construction market, the drill nozzles are represented by several models:

  • ACKO YT-160A.
  • EDMA Nibblex.
  • Sparky NP 1.8 L.
  • "Cricket" from the manufacturers of the Enekor.

By and large, all models of nozzles for drills are operating at the same parameters. The exception can be the thickness of the metal sheet, which one or another tool can cut.

After applying fixtures, the edge turns out sharp, smooth and not crumpled. It is only necessary to trace that the turnover of the drill is applied to the characteristics of the nozzle.

Those who are engaged in construction or repair sometimes there is a need for cutting metal. And if there is no possibility to purchase an expensive tool, then the cutting process can be trusted with a drill with a nozzle.

For home masters, this tool will be optimal decision and excellent assistant. It should be borne in mind that the cutting process can be entrusted to specialists who have experience and defined skills.

  • Print

stanok.Guru.

Nozzle on a metal cutting drill

Sheet metal tile is based on a metal, which is covered by several protection layers for durable service.

Metal tile layer

The finished profile of the metal sheet is bent by the method of cold pressure, alternately, first along, then into the ecr. In this case, the heating process is missing, which can ruin the properties of coatings. At the same time, the quality of the material remains high, in which it was intended initially, wear resistance to 100 years, resistant to corrosion and UV radiation and similar qualities. But in the process of laying this tile, it sometimes needs to be cut for neat and high-quality laying, while not damaging the outer layers.

The manufacturer gives a guarantee on its product, while indicating what tools should be used in order to lose this warranty.

When the sheet, the lifts should be avoided damage to the protective lacquer as the appearance of cracks and thermal exposure in the form of sparks, deformation of the material.

Therefore, the following tools are considered the most applicable: Metal Organized Handsaw, Manual Scissors for Metal, circular Saw, Electrolzik with a metal cutting nozzle, carved electronics. These tools can cut metal tile, without damaging the outer layer.

I would like to note that the convenient and usual Bulgarian in this list did not log in, as it is used with a diamond disk, which can lead to the destruction of the coating at the edges of the cut.

Disk nozzle on a metal cutting drill

When using such nozzles, you need to remember that the disc itself should be only with teeth. The main disadvantages are that it is possible to work only on a flat surface and attaching a sheet for processing.

If you need to adjust the sheet on the roof, this will not be possible. The second, the cuts can only be straight, the semicircle will cut out problematic. Much more convenient for this purpose, the acquisition of such nozzles like the carred scissors.

Metal cutting drill nozzles

Having a good drill in the household, with the help of nozzles from her you can make a universal tool for all occasions. For example, such a process as a segment of a piece of metal, even a small piece or strip, can turn into a whole problem. Of course, there are a large number of scissors on the metal of different firms, and they will cut. But the edges of the leaf cut must necessarily be flexing, cut an oval or another figure is not possible. Bulgarian is also not suitable for this purpose, the cut will be great and will have to remove burstages in the area of \u200b\u200bthe cut. To solve this problem, you can simply buy a nozzle on a metal cutting drill in any construction store.

What is the nozzle on the metal cutting drill

According to the design, this is such a gearbox that works on the principle of the matrix and punch and practically punches such a kind of punch, working with the matrix and penetrating the holes due to the transition of rotational movements into oscillatory movements.

Nozzle on a drill for cutting metal in a disassembled form

Works on the principle of carved scissors. As they say - all ingenious simply. Of course, these are not electrical scissors, but if not engaged in roofing works daily, this is an excellent option for a home workshop.

Working nozzles for metal cutting drill

The width of the cut is not more than 3 mm, the edges of the cut remains without thermal exposure, that is, the metal coating will not change its properties. The cutting itself will be made using a drill cartridge, to which the device is strengthened. Of course, the drill must have revolutions at least 2500 per minute.

The thickness of the metal cutter should be within the following limits:

  • stainless steel - 0.8 mm;
  • copper, brass, steel coated with zinc, zinc, simple sheet iron - 1.5 mm;
  • aluminum - 2 mm.

But, as well as to each tool, it is necessary to adapt to work with this nozzle.

Types of nozzles

All drills nozzles work according to one principle. The difference is only in the thickness of the leaf processed. After work, the resh is the smooth, without a burr. The only thing that may not afford to cut is the inconsistency of the nozzle and drills according to the applied turns. The most used nozzles of Russian masters, these are "cricket", "Steel Beaver", Sparky, EDMA Nibblex.

The nozzles are very universal, their use has sufficient performance, the presence of a handle helps to control the sharp from all the nozzles, the cut is obtained by good quality, you can use both pneumatic and electric drills. They do not require special settings, you can perform curly cuts, the main thing, the personal skill of the wizard.

Nozzle "Cricket"

This is such a nozzle scissor on a metal cutting drill. They are special carpent scissors, with which you can make a cut as a smooth sheet and the profile, as well as plastic and carbonate, which is also not easy to cut.

Nozzle "Cricket" for cutting metal

When using such a nozzle on a drill for cutting a profiled and sheet metal, you can cut plastic to 2 mm thick, as well as stainless steel up to 1.2 mm. It is also possible to perform internal cuts, the truth should be done for this.

It is very convenient to apply with roofing works to cut the metal tile. When cutting "cricket", deformation does not occur and the sheets do not require editing. If you even need to cut a circle or another complex element for any purposes, this nozzle will cope with this task. The only thing is that the masters will be required. Speed \u200b\u200b1500-500 vol / minute, price of 1900 rubles.

Nozzle "Steel Bobur"

It is completed with a removable matrix and Poisson. The difference from the previous nozzle is that the thickness of sheet steel, which this nozzle can cut is 1.8 mm, and the speed of the used drill must be within 1500-3000 rev / m. As well as the previous, product of Russian production.

Nozzle "Steel Bobur"

Price about 1700 rubles

EDMA NIBBLEX Sheet Metal Drill Nozzle

Excellent nozzle high Quality manufacturer, very much positive feedback, both from professionals and homemade craftsmen. According to technical specifications: the speed of rotation of the drill is at least 3000 rev / minutes, the thickness of the leaf and profile metal is up to 1, 2 mm, aluminum (sheet) to 1.5 mm.

EDMA Nibblex Nozzle

Price about 5000 rubles.

The most favorite adaptation of our masters. Country - manufacturer of Bulgaria, differs like good qualityand a democratic price.

The price of such a nozzle on a metal cutting drill in the region of 2000 thousand. The main technical characteristics include: working turns for the proper operation of the nozzle 3000 vol / minute, the thickness of the steel cut from 1.8 to 2 mm, with such parameters cutting speed 2 m per minute.

Curly scissors for Sparky Drill

Of course, in these instruments, Poisson is very frequently connected. It is sold in the same stores, where the nozzle is also purchased. I would like to note that very often the comments appear on the Internet that, Mol Poisson for Sparky costs 600 rubles, and Poisson for another nozzle about 150 rubles, but he is produced in China. Yes, in China. But the tool of the World Bosh company is also mostly produced in China, but its quality is still the highest (of course, if not running to the fake). Business in the technologies used and acceptance in quality. Therefore, pays a miser twice.

themechanic.ru.

Nozzles on a drill for cutting metal: species, features, application

The need for cutting products made of metal occurs in many situations associated with construction and repair work. Special equipment is used to perform this technological operation of different typesBut, if it is not at hand, nozzle can help a drill for cutting metal. Using such nozzles and manual electric drill, you can perform an effective cutting of small thickness products made of various metals.


Figured cutting metal tile cutting nozzle for a drill

Types of metal cutting equipment

Cut the metal sheet or a more massive metal made from various equipment.

Globlipoval machine

This device is also known as Bulgarian. With it, it is possible to carry out the cutting of reinforcement, tolstolic metal and metal products of other types. This is the most popular equipment used for similar purposes.

Circular saw for metal

Such a saw allows you to get cuts at different angles and perform them with great accuracy. Meanwhile, when using this equipment, the resulting cuts have a limited depth and a large amount of waste is formed.

Guillotine

It is high-performance equipment for cutting metal, with which the workpiece of a simple configuration is performed.

Ribbing machine and jigsaw

Such equipment allows cuttings at different angles. Both the jigsik and the belt-saw machine due to their design features impose significant limitations on the size of the products that need to be cutting.

Hydraulic equipment

This type of equipment is innovative. It allows you to perform a metal cutting with high accuracy, while the thickness of the processed product can reach up to 20-30 cm. The most significant disadvantage of this cutting method, in which the product is not exposed to thermal exposure is high cost.

As mentioned above, it is possible to use for cutting metal products, and nozzles on the drill, which in the modern market are presented in a wide variety.

Drill nozzles can also be used for cutting and other materials.

Features of the use of drill nozzles

Nozzles, with which the usual electric drill turns into a metal cutting device, is essentially a punch (pinton). Making numerous reciprocating movements in the inner cavity of the matrix, such a punch pierces the metal sheet, forming a line of the cut on it, the width of which is 3.1 mm. When using nozzles on the processing area, point exposure turns out, due to which the protective layers on the surface of the metal product fully retain all its functions.


Working part of the nozzle of cutting type

With the help of a drill nozzle, you can perform cutting metal sheets of the next thickness:

  • made of aluminum - up to two millimeters;
  • made of copper, brass, sheet iron, zinc and galvanized steel - up to one and a half millimeters;
  • made of stainless steel - up to eight tenth millimeters.

Return-translational movement of Punson, which is the main working body of the nozzle, communicates due to the rotation of the cartridge of the electric drill. It should be borne in mind that it is effectively cutting a metal sheet. Such a nozzle can only be able to use it with an electrical drill, the cartridge of which rotates with a frequency constituting at least 2700 rpm.


Examples of sections of a galvanized sheet nozzle (0.55 mm) and aluminum (2 mm)

Advantages of using nozzles for drills

Drill nozzles, if you compare them with a popular metal cutting tool like Bulgarian, differ in a variety of benefits.

  1. The resample is distinguished by high quality.
  2. When using nozzles on a metal cutting, there is no need to acquire additional consumables, which significantly saves funds.
  3. The use of such nozzle provides high cutting process.
  4. Drill nozzles are distinguished by high versatility.
  5. Due to the fact that this tool is equipped with a special handle, the cutting process with it is performed very convenient.
  6. Such nozzles are suitable for both electrical and pneumatic drills.
  7. It is indisputable by the convenience of these nozzles both in application and maintenance.
  8. With the help of such tools, you can make cuts of almost any configuration.

Despite the simplicity of the design of such nozzles, their application requires the user of certain skills and skills.

Popular models and spheres of their application

Modern models Drills nozzles allow cutting sheet metal not only in a straight line. With the help of such a convenient and easy-to-use device, curly cuts can also be performed, which is often required when installing roofing structures, ventilation air ducts, as well as gutters and other elements of the drainage system.

Using such nozzles on a drill, cuts can be made practically in any spatial position. An equally important advantage of these nozzles is that they do not require pre-configuration.


This nozzle turns a drill to electronics, working on the principle of precisely the cut, and not carving

Among the most popular models of nozzles on a drill for cutting metal presented in the domestic market are allocated:

  • "Cricket" (from the company "Enkor");
  • Sparky NP 1,8L;
  • EDMA Nibblex;
  • ACKO YT-160A.

Ambulant nozzle-nozzle for EDMA Nibblex Cutting Metal and Plastic Cutting

Differences of the models of nozzles on a drill consist not in principle of their work, but in the maximum thickness of the metal cut and a number of others technical characteristics. Modern models of shocks on a drill allow you to get smooth and neat cuts with sharp, smooth and dismissed edges. In this case, the protective coating applied to the surface of the metal sheet is not damaged and fully saves all its functions.

"Cricket"

One of the popular drill nozzles, which is compact cartridge (cutting) scissors, is a device called "Cricket". Such a nozzle that allows you to get smooth and neat cut can be used to cut both flat and specialized metal sheets.


Nozzle-scissors "Cricket" is designed to work from a pneumatic or electric drill (screwdriver) with a capacity of at least 420 W

With the help of scissors "Cricket", not only a metal sheet can be cut, but thin-sheet products made of polycarbonate and other polymeric materials. In this case, the thickness of the products, for the cutting of which these compact figurative scissors can be used, can be up to:

  • 1.5 mm - for steel sheet material;
  • 1.2 mm - for stainless steel;
  • 2 mm - for copper and aluminum, as well as polymeric materials.

With the help of nozzles for the drill "Cricket" you can cut the sheet material in horizontal and vertical planesAlso perform internal cuts on the surface sheet surface.


"Cricket" works on the principle of carved scissors

It should be borne in mind that in the place of the sheet, from where the inner cut will be carried out, it is necessary to pre-drill the hole.

"Cricket" is a good nozzle on a drill for cutting metal tile and corrugated flooring. When using this device for cutting metal, the surface of these materials is not deformed, and the cut itself is flat and neat. The nozzle "Cricket" can easily cope with such complex tasks as an art cutting and the creation of a large diameter opening in the sheet material.

"Steel beaver"

Another popular drill nozzle, with which you can perform cutting metal, is a device called "steel beaver". The principle for which such nozzles on a drill work are similar to how the cutting scissors function. When using this device, the cutting zone does not produce sparks and the metal sheet does not turn out to be thermal exposure, respectively, the protective coating is not burned, which is applied to it.


Nozzle for cutting metal "Steel beaver" is completed with a removable matrix and punch

Among the technical characteristics that the nozzle on the drill of this type has, it is necessary to highlight the following:

  1. The effectiveness of such a nozzle is ensured when rotating the cartridge of a drill at a speed of 1500-3000 rpm.
  2. The maximum thickness of the processed parts is 1.8 mm for sheets of conventional steel, 2 mm - for copper and aluminum sheets, 1.2 mm - for stainless steel sheets.
  3. The angle to which you can change the direction of execution of the cut is 360 °.
  4. The minimum reserve radius is 12 mm.

Solving the question of which tool to choose for cutting sheet metal - a jigsaw, a grinder or a nozzle on a drill, "should first estimate the tasks to solve which they are necessary.

Drill nozzles are a good option For home masters and small construction teams. When the volume of work on cutting sheet metal minor, the use of such a nozzle is an optimal solution. Choosing this device, it is necessary to pay special attention to the fact that the characteristics of the drill are included in which it will be used, corresponded to the characteristics of the tool itself.

With the need to cut any metal products facing almost every specialist engaged in construction and repair work. Many professionals for high-quality metal cuts use a variety of tools, starting with cutters, grinders and ending with hand scissors. But what to do if there is no such tools at the right moment, and it is extremely necessary to cut the metal. It is possible to carry out this process by using a conventional electric drill. Now in construction stores for these purposes, you can purchase specialized nozzles on a metal cutting drill.

What is a nozzle on a metal cutting drill?

According to mine constructive features The nozzle resembles Punson or Shplongton, which due to the matrix performs metal breakdown with a large number of repeated movements. After that, a strip of the necessary form is formed in the product being processed. In the process of cutting, the impact on the metal occurs pointwise, which helps to preserve the object's integrity. A similar nozzle repeats the work.

With the help of nozzles, you can handle the metal, the following parameters:

  • aluminum with thickness of products on average up to 2 mm;
  • stainless steel up to 0.8 mm;
  • brass, copper, galvanized steel, iron sheets, zinc with a thickness of up to 1.5 mm.

It should be remembered that the softer the material being processed, the greater may be its thickness.

Features of the work of the nozzle

Before the direct work, the nozzle is reliably fixed in a drill (cartridge), which leads it into action. The principle of operation is almost completely identical to the process of operation of electromechanical scissors, which, without particular difficulties, perform straight and curly cuts. To ensure high quality cuts, competently select the number of revolutions. For example, for metal a small thickness, it will be good from 2700 to 3000 thousand revolutions. It follows to the sow only when the drill scored the required level of revolutions.

Typical types of drill nozzles

On the market you can find several models of drills for metal:

  • nozzle "Cricket" (acts by type of carved scissors) - used to cut the thin metal metal. Consists of two special cutting heads. The nozzle "Cricket" is often indispensable in the implementation of roofing works. For example, such as cutting metal tile or professional flooring. The use of such a nozzle allows you to not deform the material and get smooth and beautiful sections. Unlike the render of the grinder, the nozzle is capable of performing more clear without bursowns of the edge. With the help of "Cricket" you can also drill a neat round holes of large diameters, including artistic cuts. If necessary, you can carry out work on horizontal and vertical surfaces. As an additional criterion, the "Cricket" nozzle helps during the cut processing edges with special abrasive materials. The price of such a tool is often located within 4000-7000 rubles;

  • nozzle "Steel Bobur" - In most, this type of nozzle is used in cutting profile and flat sheets of metal. According to its principle of operation, the cutting mechanism of the nozzle is very strongly reminiscent of the processing of the material with the help of cutting scissors or "guillotines". In addition, applying the "Steel Bobur" nozzle in the process of operation does not burn the protective layers of the metal coating of sheets and thereby not formed by sparks. The use of the nozzle eliminates the risk of the possible appearance of chips or deformation of the edge of the cut. This nozzle can perform polycarbonate, aluminum or plastic. The distinctive characteristics of the nozzle are: rotation of the drill from 1500 to 3000 thousand revolutions, the minimum incision radius is 12 mm, the ability to change the angle of cut 360 degrees, the thickness of the materials - copper and aluminum in 2 mm, stainless steel - not more than 1.2 mm , ordinary steel - up to 1.8 mm.

There are a large variant of the execution of this tool from different manufacturers, however, the principle of operation for everyone is the same.

The main advantages of nozzles

As a rule, experts allocate several main preferential differences in the drill of the Bulgarian:

  • universality of the tool;
  • easy service and use;
  • high quality cut;
  • good performance;
  • the ability to do the holes of any form;
  • saving funds due to the absence of the need to apply additional consumables in the work;
  • ease of operation of equipment achievable due to the equipment with a special handle;
  • the possibility of working from a pneumatic or electric drill.

It should not be forgotten that certain skills are needed to ensure high quality cut. Of course, in contrast to household or professional tools of a complex configuration, it is not necessary to adapt to work with the nozzle. Any newcomer may well cut through 1 hour to 10 meters of metal. The nozzle can be attached to any type of modern drill.

In general, it is not necessary to think that the nozzle on the metal cutting drill will be simultaneously a full replacement for several tools. Unfortunately the capacity of this equipment, not always enough in comparison with electrical scissors professional level. In addition, the supported thickness of 1.5 mm does not allow any really serious work.

If you do not take into account the degree of productivity of the instrument, then the nozzle can be completely purchased to perform not too much the work. In such situations, the nozzle will significantly save a lot of time and money.

Nozzle-scissors "Cricket" ENKOR 14210 is used in conjunction with any drill. Designed for cutting metal with a thickness of up to 1.6 mm. Fastened in the cartridge, which leads the mechanism of the nozzle. Works on the principle of cutting scissors. Allows both linear and curly cuts, suitable for cutting material with ventilation and roofing.


The nozzle for cutting metal "Cricket" produced by the company ENKOR is intended for installation on devices with rotary cartridge - they can be represented by drills or even small.

Due to its design, it is capable of completely replacing specialized scissors, carrying out a lightweight cutting of steel, aluminum and other metal sheets. The advantage of the model is small dimensions, a small mass, as well as a thoughtful design that minimizes the percentage of the torque loss.

Video review Encore "Cricket"

Application with screwdriver AKM1802



Characteristics of the work of nozzle-scissors "Cricket" for metal up to 1.6 mm Enkor 14210

The device is intended for a complete set of screwdrivers and network drills, which have no power no less than 0.4 kW - this indicator is the average for this category of tools. This somewhat limits its area of \u200b\u200buse, as instruments with a less powerful drive can be presented on the market. The internal mechanism is a standard hexagon - such a shaft provides a more reliable fastening than round and has a significantly less probability of slippage.

The maximum thickness of the leaf steel is not subjected to additional processing is 1.6 mm. When working with doped or high carbon materials, the manufacturer recommends reducing this value to 1 mm. If the operator needs to carry out activities with aluminum, copper and other relatively soft metals, then the sheet may have a thickness of 2 mm. Thanks to this, the "Cricket" nozzle is a good alternative to the traditional manual tool. The width of the cutting track does not exceed 1.6 mm - this value allows to provide significant material savings when performing complex works with small objects.

Also, the device functionality includes the ability to pre-drill holes with a diameter of at least 11 mm. The length of the nozzle is 180 mm, which makes it possible to produce work in a limited space with maximum level facilities.



Features nozzle-scissors "Cricket" ENKOR 14210

The undoubted advantage of the metal nozzles is the lack of consumables, in counterweight cutting circles for the grinder and jigsaw. "Cricket" will help not only quickly cut the sheet metal, but also quickly make a hole of a large diameter in the sheet metal. Also with this nozzle, you can cut holes for an arbitrary form from previously drilled holes diameter of 11 millimeters. In addition to the above, it is important to indicate that the "Cricket" nozzle is very simple and easy to use, does not require adjustment at all, which means that even a newcomer will easily defeat it, and the professional will appreciate the convenience and speed of work.

For more reliable fixing fixture, a plastic handle and punches are used - they are supplied. This allows you to significantly improve accuracy permissible species work. A mass of 0.4 kg does not increase significantly on the operator's hands compared with its own weight of the electrical appliance. A drill nozzle that allows you to cut a sheet metal to 1.6 mm thick. Works together with any drill.

For proper selection The number of drive revolutions shows excellent cutting results: the edge of the metal does not matter, and at the same time they do not get sharp.

Characteristics


Contents of delivery

  1. cricket
  2. blister



Features of metal scissors ENKOR 14210

  • Perfect option for cutting holes in suspended ceiling (panels) for point lamps.
  • To work with metal sheets up to 1 mm thick.
  • Well cuts no thick metal 0.3-0.4 mm.
  • Be sure to use protective glasses and gloves.



Dignity

  • Suitable for cutting metal tile, both along the way and the waves.
  • Cutting edge without burrs.
  • Does not warm and does not smear the coating
  • Indispensable for working with a painted sheet, metal tile, which is not allowed to cut with a grinder.

What do metal cut at home? In 90% of cases with hand scissors (we are talking about fine metal tin). The method is infertility, inexpensive, but not devoid of flaws.

  • At a minimum, to do a long incision without burrs is quite difficult.
  • Since scissors are located along the sheet, the cut planes required to breed up and down. This makes it difficult to work, not to mention the fact that the edges later need to align.
  • If the workpiece is not flat, but with rigidity ribs (for example, professional flooring, or figured "under the tile" coating for the roof), to perform a cut by conventional metal scissors is almost impossible.

A great physical effort is required. If you need to cut several meters at once, then it turns out a good training, as in the gym. Often, for such works, Bulgarian with a cutting disc is used.

It turns out quickly, relatively smooth and not at all difficult physically. However, the edges require subsequent treatment, and the metal on the edge is subject to undesirable thermal exposure.

If you are working with sheets of profiled metal-plastic "Tiles", the protective layer is burning in the place of the cut and loses aesthetic appeal.

Progressive way - Electric scissors for metal with vertical location of the blades. However, this is a notched tool that is extremely rare (how often do you re-cover the roof?). Therefore, there are more practical devices on sale: nozzle on a drill for cutting metal.

In essence, it is a gearbox that converts the rotational movement of the spindle into oscillatory. Of course, in its characteristics, the device is inferior to a full-fledged electrical scissor.

However, the nozzle on the drill is inexpensive, besides, you do not buy a ready-made tool (scissors with a motor), which most of the time is dusting on the shelf. Drill is practically in every home, if necessary, it can be easily turned into a progressive cutter.

Varieties of nozzles

Classic nozzle on the drill - metal scissors. The second name: "Beaver".

mOB_INFO.