What inflate balloons. How to inflate air and helium balls. Life expectancy of foil balls

Surely, each person noticed like balloons, during an inflation to burst right in their hands, as well as after they were picked up and hanging on the wall. For what reason does this happen? Now we will understand.

Balloons differ in size. In no case, it is impossible to inflate the permissible threshold, thanks to this impact, the ball becomes more vulnerable to damage. In case such a ball did not burst during an inflation, it will burst a little later. For this reason, in obligatory order before inflating, you need to know the maximum permissible size of the ball. Find out whether the ball will come correctly, you can on the tail. In the event that the tail will be very much, then you inflated the ball too much, and next time you should not do that.

In compulsory, the balls need to inflate indoors where there is no dust and drafts. In case the dust is present in the air, it makes the ball more susceptible to the explosion, and also reduces the service life of the balls.

The balls are undesirable to store under the right sunlight, as well as in the places of a sharp decline in temperature. In the case of influencing the balls of ultraviolet rays, the structure is rapidly destroyed and the ball can burst with inflammation. In case the ball is in the open sun, it can reduce the life of a ball for 2-3 hours. The temperature differences are also very significantly affected by the quality of the balls. In the event that you make them from the cold room in heat and immediately inflate, then such balls will last long, or burst right away. For this reason, it is better not to store in the cold. Reducing or increasing air in the ball can also lead to the fact that it burst.

Well, of course it is impossible that the balls fall on hot or sharp items.

It is worth noting that in order for the gel balls Kiev worldwide as long as possible, they can not:

1. Pass
2. Eliminate contact with dust;
3. Prevent the impact of sunlight;
4. Exclude sharp temperature differences.

In order for balls with helium a little longer, they are allowed to cover with special High Fleet glue. This type of glue is absolutely safe for human, pets and the environment. It is for this reason that it is so often used. The balls with helium serve much less than ordinary, for the reason that the molecules are too small, so they quickly pass through latex. The glue contributes to the fact that the gas remains longer in the ball. In the case of using such glue, the process of operation increases to 3 days.

Where can balls be used?

It is worth noting that helium balls, much better look rather than ordinary, however, it is worth noting that their service life is slightly lower. One thing is known for sure, imagine any holiday without the presence of balls is simply impossible. Choose balls in your own taste, the main thing is to store and use them on the advice, which were presented above.

Balls can be used on children's matinees, it will make a holiday brighter and colorful. Birthday, this is a special holiday for any baby, respectively, always want this day to remember for life. The use of balls on this day will make a holiday bright and cheerful. Of course, for each holiday their definite balls are used. For this reason, you must choose exactly the balls that are suitable for your event. Happy Holidays, excellent mood And the most colorful balls you and your children. Smiles and joy of a cheerful mood!

Inflating balls helium directly from the balloon

Latex balls are most often inflated through the threaded attachment of the cylinder with helium. The inflation process is divided into three stages:

• shadow's necks on the balloon valve,
• filling a ball helium,
• element balls from a balloon valve.

For the dressing of the ball, the balloon valve is applied as follows:

• capture a bowl between the indexed and thumbs of both hands and stretch;
• the bottom end of the stretched neck of the ball is at the thread of the attachment of the cylinder;
• raise the top end of the neck of the ball and roll it over the tuning of the attachment of the cylinder.

The neck of the ball should be deeply lying on the threaded connection of the cylinder and grasp it tightly. So deep so that when the ball is inflated, there was no need to hold the neck of the ball with hand.

To fill the attached ball, helium requires replenish the flywheel of the cylinder valve in the direction against the clockwise movement. The more the cylinder's valve is open, the faster the helium fills the ball, and vice versa. Therefore, for beginners it is recommended to open the valve of the cylinder as careful as possible, until the required skill appears. When the inflounted ball is reached the optimal size, the helium flow is stopped by turning the valve flywheel in the direction of the clockwise stream.

Element balls from the valve of the balloon is performed by two hands. In a place where the neck of the ball goes into a cylinder, the bowl of the ball is clamped between the large and index fingers of the left hand. An index finger of the right hand twist the neck of the ball behind the ring with the threaded attachment of the cylinder. It is impossible to just pull the ball from the valve of the balloon, because In this case, the valve thread can cut the neck of the ball. Inflated ball tie at the same time with a braid.

Testing inflated helium balls

Inflatable helium balls, it is necessary to tie quality and quickly. Beginners are often acting as follows: first they tie the knot on the cervical ball, and then tie the ribbon to the knocked ball. We consider this way too long and not reliable: the rigorous node can unlease and the ball will fly away.

Much faster and more reliably tie the knot on the neck of the ball simultaneously with the braid. As a result, a node is obtained, which claws the neck of the ball and the braid passed through it.

Balloons are able to decorate any holiday and create a unique atmosphere in the room.

Purchase the ball first to the maximum size, and then release 10% of the air from it, so you can extend the service life of the balloon, since its surface will become more elastic.

Before filling the ball helium, fill it with air, and then lower. This additional maneuver will allow you to increase the size of the ball when it is inflated by a helium by 10% and increase its service life. Also, the gas leak can also be avoided if the ball turns out to be a defect.

It is not necessary to inflate balls in advance with helium, because the inflated balls will be able to hold out in the air no more than 18 hours (with a diameter of 30 cm). Best to inflate balls directly on the day of the celebration.

Sources:

• balloons how to inflate

You can inflate balls at home with a homemade hydrogen installation. For its manufacture, you will need a bottle, copper sipop, salt, syringe, hose and copper and aluminum wire.

Balloons are an unchanged attribute of the holiday, but what to do if you have to inflate a large number of balls, and there are no cylinders with helium? No problem. You can get our own hydrogen, even without leaving home. To do this, you will need a simple plastic bottle, syringe, hose, natural cork, copper vigor, copper wire, aluminum wire, and better aluminum foil, sealant, food salt and actually balloons themselves.

As a substitute for aluminum wire or foil, you can use an aluminum can, the only condition - you need to clean it interior surface From paint and protective polymer layer. And yet - all work is best done in protective gloves and glasses.

Hydrogen installation assembly stages

In the cover of the bottle, you need to drill two holes: one under the hose, another under the syringe. For better fastening of the syringe on its tip and in one of the holes on the lid, it is advisable to make a thread. Secure the screws and the hose in the holes done by the holes, and the locations of their connections are marked with a sealant. To put a plug on the free end of the hose - it will secure the ball. To the piston of the syringe, you need to attach a wire from copper, the place of the joint is also handled by a sealant. To the free end of the attached wire is required to tie a wire from aluminum or crumpled foil. The piston will ensure the free movement of the aluminum reagent in the bottle.

Looking at the aluminum reagent into a bottle and closing the lid, you can get a ready hydrogen installation. To start its operation, the cover from the bottle together with the aluminum reagent needs to be removed, and in the bottle, fall asleep the copper vaporace and food salt in the ratio of 1: 1. Pour water and wait until the mixture is completely dissolved. The contents of the bottle need a cold, for this it can be put in a pelvis with cold water. On the plug fixed on the end of the hose, the air balloon is put on, after aluminum you need to immerse in a solution from the mood and salt and tighten the lid.

How is the ball of inflation

The reaction will be submitted immediately: the highlighted hydrogen will fill the ball. As the aluminum oxide film dissolves and the heating of the solution, the reaction will only be accelerated. In the case of too violent hydrogen release, it is possible to remove aluminum from the solution, pulling the piston of the syringe. Tensioning the balloon directly on the neck of the bottle is strictly forbidden! The resulting balls can be left in the form in which they are, and you can get off with white or black packages, as well as attach the LED and run the ball in the dark.

When decorating holidays by balloons, balls often use helium inflated. Tell how to inflate helium correctly and tie the balloons.

You will need

• - Cylinder with compressed helium (10 liters or 40 liters);
• - Latex air balloons in size 12 ";
• - tape for tosing inflated balls - a decorative polypropylene tape with a width of 5 mm;
• - Scissors for cutting braid.

Instruction

Proper and safely install a gas cylinder helium. During the inflation of balloons, helium cylinder must be installed in a way that excludes its fall, tipping up and any movement. Large cylinders (40 l) are located in the standing position. Small cylinders (10 liters) can be positioned horizontally provided they are reliable fixation on the table or on the floor.

We prepare braid. To link helium balls, as a rule, slices of braids are used with a length of 1.5 m. The desired number of the ends of the braid (by the number of balloons) we cut with scissors. For children's holidays, the ends of the braids are done longer: 2.0-2.5 m - in order for children to get them. The main thing is that all the ends of the braid have equal length.

It can sound strange, but balloons must still be able to inflate correctly. Let's tell you how to fill the ball with air or helium and from which latex and foil balls can burst.

How to inflate a bowl from latex

The balls are not made of rubber, but from a subtle latex. It is durable, but is destroyed from sunlight. So that the ball does not burst with inflammation, follow several simple rules:

• do not inflate the latex ball until you stop - burst from light touch;
• it is better to inflate to a reasonable limit, and then release 10% air;
• to control the size of the balls, use a pre-cut pattern from cardboard.

If you have to inflate a lot of balls, do not risk health and order a special pump. With it, you can quickly fill in air dozens of balls for binding in garlands. Inflating their lung power, you spend all day. To fill the balls, helium you will need a cylinder with this inert gas. It can be bought by taking a cylinder for rent. But helium is quite expensive gas, and in the absence of skill losses will be too large. Before filling in helium, you first need to inflate the ball with air and inspire it. The ball stretches a bit and welding more helium, and you at the same time check it on marriage.

Tie the ball correctly

And here is the latex ball will come, now it is important to tie it correctly. Pull the tail with one hand, clamping another neck. Tighten the tail and wrap around the finger. Then thread the tip in the loop and tighten. At this stage, the ball can break and carry with a funny sound or burst due to strong tension in the area of \u200b\u200bthe tail. The ball with helium is better to tighten with a special retainer.

Foil balls

They are equipped with valves that overlap the reverse air and helium output. It simplifies the procedure for the inflation of such a ball, and it does not need to be tie, which saves time and effort. However, the balls from foil have their secrets. For example, you should not pump a ball - it may disperse on a glued seam, leave the folds from the sides. Fill with air such a ball must be uniformly. When filled with helium, special adapters are used - do not forget to order them. And the balls of foil with helium are expanding on the heat and shrink on the frost by 15-20%.

And so that everything went, how conceived, it is better to order balls from us. Fill the balls of any type of air or helium.

Folgized balls produce from pieces of metallized lavasan film, with a colorful pattern or one-photon coating, connecting them with thermal welding. Since the lavsan film with applying metal is very similar to foil, they are most often called "foil", much less often - "Malar" or "Lavsanov". Foil balls are the following types:

1. The forms are made in the form of various stars, a circle, heart, crescent from a monochrome film of bright colors. Separate manufacturers cover their holographic paint, giving the transfusion and paint sparking.


2. With a pattern - produced in the same forms as the designer, but they are applied or inscriptions for all festive cases of life.


3. Symbols - monophonic, as a rule, are made in the form of numbers or Latin letters with a height of 80-90 centimeters.


4. Figures - made in the form of animals, the heroes of animated films and fairy tales, various items. There are simple or volumetric.


5. Walking figures - inside them are special weights that do not give them to take off. With the slightest draft, the figure moves on the floor, turns, waving his head.

What and how to inflate the foil ball right?

The balls of small sizes are often filled with air, in this case the ball is usually attached to the tube with a clip. The volume size of 18 inches and more fill helium. All foil balls at the base are inlet (it is the reverse) valve through which it is inflated both with air and helium.

To solve the issue, how to inflate the ball with air, you can use a manual pump, which has several nozzles and will suit all kinds. If there is no pump at hand, you can inflate the mouth through the tube from the cocktail. In this case, it is necessary to gently insert the tube into the inlet towards the center of the ball, to promote it with 5-10 centimeters inside and make exhale inside. If necessary, you should fix the foil ball or gently push the tube slightly deeper. After inflation, you just need to pull the tube, check valve Immediately closes and the air will not be released.

To fill foil balls, helium will need a portable cylinder with helium, nozzle to a balloon and an adapter to inflate the balls of this type. The lower, the wider part of the nozzle is screwed into the cylinder, then adapter is screwed into it. This adapter is the tube that needs to act just like when airing air. It is advisable until the balloon is discovered to blow the ball through the air tube (just one exhale to make sure the air goes). Then you need to press the neck of the ball to the adapter, open the crane on the cylinder and start filling the ball. First, it is inflated quickly, but almost filling, helium begin to serve small portions to avoid a ball into the ball. When a folgized ball is completely coming, the tap is completely wrapped, the ball is neatly removed from the adapter, tapes with a braid or seaweed.

A well-filled ball does not need to be tied up, since the check valve holds the filler inside. But so that the ball does not fly away, the braid is tied to his neck. If you bind the ribbon above the inlet, then the tightness of the valve can break and the ball will lose elasticity, so it is necessary to bind the bracket below the inlet. Balls without a valve are searched with a specialized device - a sealer, and two welded seams located above the inlet of the inlet are formed on the neck of the filled ball. Then it is taped to it.

Life expectancy of foil balls

The life of their life is a period of several days to a month. Helium or air slowly goes through the check valve or through the seams that are connected to the parts of the ball.

In addition, the life expectancy is influenced environment: Cold, heat, rain. Therefore, it is desirable not to expose the balls a large temperature drop, do not use them in the rain or in the wind, as well as correctly fill and tie them.

Second life of foil balls

In order to save money, when decorating the holiday, you can reuse the used foil balls, but for this you need to correctly and gently release all the air from them, and store them in the unfolded form in a dry and cool place, paving the paper between them.