Plastic windows are saved from street noise, provide a comfortable air temperature of an apartment, a private house. However, after installation, they require. Setting the locking mechanisms is needed every off-season - only then the windows will perform the task supplied before them. Today's article will tell how to translate the windows in the winter mode, for which it is necessary when such actions are performed. Along the way it is worth understanding the features of the locking mechanisms, the device, some nuances of functioning. We will help us with photo and video instructions, explaining the algorithm in detail the actions performed.

Immediately make a reservation that with the lack of knowledge and experience, our edition recommends contacting the professionals of his case. Specialist companies will advise on all possible issues and offer the most profitable solutions to problems. Well, for those who still want to independently do this issue - a small reference.

Modern plastic windows are adjustable by the strength of the clamps in three modes:

• summer - The window sash presses weakly. This provides air circulation in the room, implementing. Sealing rubber wear minimal;
• winter mode On plastic windows provides a dense clamp. Air circulation is absent, which ensures the preservation of heat into the dwelling. Load on the maximum sealing gum;
• standard - The average position of the eccentrics (PACF). More often, the installers leave shut-off mechanisms in this position. The only difference is that the professional professionals are relevant to their reputation show the owner, how to translate double-glazed windows in a winter or summer mode, and negligent (koi, unfortunately, most) do not bother themselves with explanations. Standard mode is intended for offseason.

For which plastic windows are switched

Enough 2-3 years not to switch the "Winter-Summer" mode on plastic windows to after, even with the right adjustments, began to think from under the windowsill or balcony doors. Consider problems arising from incorrect settings.

The first is a disturbance of the microclimate of the room. Excessive contributes to the occurrence of condensate on frames, double-glazed windows and walls, which leads to the appearance of mold. "Summer" settings in the winter lead to heat loss, there is a need. The result is increased gas accounts or.

Important! Using the winter position plastic windows In the warm season will lead to rapid wear of seals. The result is the uselessness of any subsequent adjustments. Exit - replacement of sealing gum standing non-sash.

Switching plastic windows: advantages and disadvantages

Disadvantages of window adjustment may occur only with incorrect actions. homemade Masters. If everything is done correctly, the switching of the modes will only benefit. We will figure it out in what cases it is justified.

Timely switching will extend the service life of the windows, even if for some time these actions were not produced. Drafts in winter or dust hit in summer due to the rendering of accessories for winter mode. Let be long, but for a year or two will be delayed. Schedule loops is eliminated in the same way. Replacing accessories is an extreme measure.

Good to know! Incorrectly displayed modes can cause the window to join or the door separately in the ventilation position or together with the opening.

Determination of the possibility of changing seasonal plastic windows

Not all models of plastic windows have the ability to change modes. To understand whether it is present on your glass packages, you need to look at the shut-off valves. Eccentric, located in the middle, maybe oval form or in the center it will have a hole under the asterisk or hexagon. This indicates the presence of a winter regime on plastic windows. The photos presented below will help the reader to deal with this question.

The algorithm of actions when adjusting windows with different pinches is identical, but their position may differ. Let's try to deal in detail with the types of eccentrics.

Forms of escentrics and nuances of translation modes

The oval pin after installation is more often located diagonally - this is a standard position, mean between winter and summer. Horizontal position speaks of winter, and vertical - about summer mode.

If eccentric shut-off reinforcement Round (under the hexagon), then its position is the following. Put forward in the direction of the street - winter, located in the center - the standard, drowning towards the apartment -Leto.

The third option is a rounded hexagon pin, which does not move when turning. In this case, it is a risk that indicates the correct position. To make it easier to understand, we offer to view the pictures, how to translate the windows in the winter mode.

How to translate windows in winter mode: preparation of double-glazed windows

Before, you should produce preparatory work. The first thing to be done is to remove the lubricant from the knife shut-off knots so that along with it when adjusting does not fall inside the dirt and dust. After all the works produced, the mechanism is again lubricated.

Very important! Rubber frame seal before cold should be processed. You can do this with a lubricant (based on silicone or glycerin), but it is better to use a silicone spray that is sold in all economic and automotive stores.

How and when plastic windows are translated to winter mode

Specialists recommend translating shut-off mechanisms from summer for the winter only in extreme cases when drafts are becoming sensitive. However, this is suitable only for the warm climatic zones of Russia. The optimal will be switching at the beginning of the heating season.

Specifying the need for adjustment can and drunk a glass or a small appearance on it from the inside of ice.

Helpful information! Before switching the windows to the winter mode, you should carefully examine the rubber seal. Perhaps adjustment of the fittings of the sash is correct, and the seal cracked or broke. In this case, it is necessary to replace it. For one winter you can buy cheap seals, but they do not pass more than the season.

Other plastic window frame adjustment parameters

Recommending how to translate the windows to the winter mode with a hexagon, a screwdriver or pliers, you can move to the rest. After all, with time, the frame may be a story, and one side will lay down the tight other, which is unacceptable. This creates a load on the window fittings and contributes to the appearance of drafts.

Adjusting the sash vertically and horizontal is carried out from the bottom loop. Remove the protective pad out of plastic and find a screw with a hole under the hexagon located on top. When turning the screw clockwise, the frame will start raising. Turning counterclockwise, lowered the glass pack. In order to push the frame from the frame or, on the contrary, set closer, we use the screw located on the side at the bottom of the loop.

Important! If all the adjustments are made correctly, and the problems of drafts did not disappear, this indicates the wear of seals, the factory marriage of the frame or improper installation of the flaps. We check the sealing gum, and if they are normal, we appeal to the claim to the installer. That is why it is important to perform the settings in the first year of operation - the possibility of warranty repair remains, and sometimes replacements.

Article

Translation process:

• First of all, it is necessary to find all the eccentrics. Depending on the type of window fittings, there may be several. Typically, these are three troughs on the end of the sash side of the handle, one - from the opposite end, where the loops are installed, one - on the upper plane, the other is on the bottom.

Comment

Head of the Brigade of the repair and construction company "House Premium"

Ask a Question

"For the winter mode - this is adjusting all the eccentrics at the same time. It was not transferred to one of them, which means that the clamp will be loose in some plane. And all the operation done before that did not make sense.

"

• Now we need to clean the trough and the rest adjacent to the plane and items. The goal is not to give dust and pollution to get into the plane of the displacement of the eccentric. That is, in this way the task of excluding the mechanical impact on the adjustable node is solved.

• After it is recommended to lubricate the accessories.

• If the hedge of the pin is round, we are looking for a label at which the displayed mode is determined.
• Now all the eccentrics must be alternately rotated to the required position. This requires tools corresponding to the form of deepening on the heap of the rotary mechanism. If the head is oval, then the translation is carried out by conventional pliers.

• Now you need to check whether everything is done correctly. Check is better to carry out a notebook sheet, as described above. There is no better option.

It is necessary to warn that some manufacturers of window fittings make eccentrics in the form of a recessed mechanism. That is, their hat is flush with the plane of the end of the window sash. Before moving euro windows in the winter mode, you need to pull the heats of the TsAF from the nest. Rotate them to the desired position, and then drown again in the sash.

By the way, before moving the windows to the winter mode with a hexagon, you need to choose this tool. Its size is 4 mm. Made a device from instrumental steel in the form of a tool curved at an angle of 90 degrees. It is easy to work with it, because its principle of operation is a lever that increases the effort several times.

Video process of translating plastic windows in winter mode

The video below shows how to properly translate the windows to the winter mode. It is clearly shown another variety of window fittings, where when translating it is not necessary to use additional tools. Everything is done by hand. For this, the clamping roller is simply delayed over and freely rotates relative to its axis. That is how switching is performed.

Attention! Regardless installed mode Pressing plastic windows open to ventilating in the standard way.

Requirements for setting up window fittings

The question is how to switch the windows to the winter mode is not only in a simple turn of the clamping rollers. There are certain requirements that must be performed:

1. During the first year of operation, establish a standard position. Rubber seals are still in good qualitative state, so they can provide a dense adjoining of the sash to the frame.
2. It is impossible to keep the winter regime in the summer, and summer - winter.
3. Translation must be performed twice a year according to the temperature on the street. For example, if in November it is still warm, that is, a plus temperature, then you should not make a translation during the cold time. It is better to wait a bit.

If even in the winter position of plastic windows between the sash, the impress and the frame, it means that the rubber seals were wear out, their operational resource was developed. What to do in this case? Change new ones. Make it easy.

Article

How to prepare plastic windows for winter?

How to prepare plastic windows for winter?

Metal-plastic profiles are an excellent solution for glazing residential and premises. They perfectly protect the room from heat leakage, street noise, drafts and dust and have significant advantages over ordinary wooden Ramami. The quality product is able to listen to 15-20 years without any problems.

So that in the process of exploitation, unexpected inconveniences, it is necessary to periodically take care of the PVC design, namely: to translate the winter and summer mode. Our main topic is the preparation of plastic windows to the winter season. We assure: it is not at all difficult and set to anyone if you follow the list of recommendations below.

We start with cleaning

The first thing you need to do is to thoroughly wash the window. There are not only double-glazed windows, but also profiles, windowsill, plastic dispensers. Intremely not recommended to use caustic or abrasive washing agents! They can plastic coating, leaving the ugly divorces of a darker or yellowish color on it. Remove with soft gels for washing.

For security reasons, it is not necessary to wake up for cleaning from dirt with a metal washcloth - it will probably scratch plastic, and its aesthetic species will deteriorate. You need a soft flannel rag, rag or sponge. Washing not only from the inside - but if possible and outside.

Special attention is paid to the drainage channel. Get rid of stuck garbage or seams can be carefully implemented by ordinary toothpick. By this you warn the stroke of water in drains and obstacles in the movement of window sash. To pVC windows In winter, they served without problems, it is also necessary:

And a little more about seals. They must be periodically lubricated with a special lubricant or technical vaseline. Timely care will help to avoid drying and freezing. But with a preliminary inspection, wear was revealed - do not be discouraged: the replacement of the seal is easy and most.

Pick up the desired option in the construction market and set the old one (with a flat screwdriver). The landing place is desirable to handle lubricant. After - it covers the entire area of \u200b\u200bthe sealant.

Configuring window accessories for winter period

Before approaching the cold, it is necessary to adjust the window accessories: the frame must be more tightly tightened to the glass chain: only so can exclude drafts. To perform an action you need a hex key. If you do not know how to adjust the accessories, use our prompts.

• Horizontal sides are adjustable from below and from above. Consider attentive: they have a special hole for the hex key.
• Adjusting the top panel is performed when the window is open. Rimming the edge is carried out by rotating the key to the right.
• If the window is on the first floor and it can be reached from the outside - you do not have to open the sash. Located below the loop allows you to adjust the vertical sides. To get to the hex hole - pre-remove the protective cap.
• So that the force of pressed the profile frame increases - you need to follow the eccentrics. To do this, bring them to the right. The guidelines will serve specially applied marks that determine the force of pressing. Attention! If the tag is turned toward the seal - the clamp is strong. Often, eccentric turns conventional pliers.
• In places where hinges come, the devices that are responsible for the power of the clutch are placed. How to recognize it? According to that, so much protrudes. The longer, the stronger the clamp of the frame to the window. Measures usually produce a key hexagon.
• In no case do not allow a strong pressure on the tongue! This will inevitably lead to rapid wear and complete failure of the window seal.
• Do not neglect the regulation of the loops, translating the PVC design to the winter mode. Please note: on the bottom loop, most manufacturers have provided a protective cap that is removed. After that, the adhesive bolt is performed.

If you spent these manipulations - the adjustment of the plastic windows to the winter is completed. Everything is simple enough: the main thing is neat and consistent. But it happens like this: everything is done correctly, but the window still poorly retains heat, and the area penetrates the room. Why this happens and how to fix the situation - we tell further.

Preparing plastic windows for winter: how to save maximum heat?

PVC profile does not keep warm, misses the noise, and condensate accumulates on the windshop? There was depressurization that requires immediate intervention. The most common causes of the problem:

• There was a shrinkage of the walls after plastic windows were installed. Solve the problem is easy - just adjust the fittings.
• Aligned its seal period. Here will help the replacement that we wrote above.
• The place of the junction of the slope and the frame is leakage. We will have to remove the slopes, make their insulation and mounted back. If you do not have enough experience to carry out this manipulation - invite a specialist.

Single-chamber and two-chamber glass windows with strong cold needs additional insulation. It is possible to produce it using a film, preferably - frost-resistant. For high-quality insulation, you need to know that:

• Punching films indoors, and not with the outside of the window most effective and energy saving.
• Glue film, control uniformity and tension force. If this is not done - breakthroughs may occur on it.
• It is not worth replacing the film with minor damage. Gently creep the breakthroughs with scotch.
• The best way - Film, resistant to frozen (has a high density and characteristic yellowish tint). We do not recommend buying it on the market. It is wiser to visit a large construction store that implements certified products from proven manufacturers.
• At the same time, durable and quite decorative, for sticking windows from the side of the room - a greenhouse film. And also - she is durable.
• Do not use building stapler or stationery buttons to secure. They rut the material. You will need only scotch.

Recently, an eco-friendly and reliable PVC insulation is used. It is resistant to deformities and large frosts. We hope we exhaustively told about how to prepare the euro windows by winter and were helpful. Good luck!

Evgeny Sedov

When the arms grow out of the right place, live more fun :)

Content

Plastic window structures Different companies have similar adjustments. When they are installed, the average clips density are set. Over time, under the influence of wear or other factors, the sash can prick and start clinging the frame or an impos. When the temperature drops, the cold air from the street can start penetrating into the room. In all these cases, it is necessary to adjust the windows that can be conducted independently, if you know how to adjust the plastic windows for the winter switching the clamping settings from summer to the winter option.

What tools are needed to adjust the plastic window

Plastic window systems have become the most popular product that is installed during construction or repair as a simple apartment and a chic high-rise mansion. With all the variety of window fittings used in their creation, similar mechanisms are used in all systems. Preparation of plastic windows to winter begins with the first cooling. The main tools that may be needed to adjust windows are:

• high-generated g-shaped width of 4 mm wide;
• screwdriver flat 4 mm;
• crushing cruciform;
• pliers.

How to translate windows in winter mode

In order to prepare euro windows to winter periodIt requires a seasonal adjustment of the clamping of plastic windows, at which the following steps should be carried out:

1. Adjust the opening sash vertically and horizontally - it should not be clinging the frame and clamping strips.
2. Adjust climbing strength to the frame. Adjusting the clamp is performed using adjustable pin or eccentrics, the number of which is 4-5 pieces on eurokeshoes, on the doors - 6-8 pcs.
3. If you have traction, with a maximum fit to the frame, it is necessary to replace the seal. Then check the craving on the middle position of the axle or eccentrics.

Climbing to the frame is based on the engagement by rounded elements of the clamping slave, when turning the knob down. These rounded elements made in the form of an oval are called pinges, and made in the form of a circular element with a shifted axis of rotation - eccentric. The rotation of the axle is produced by pliers. Their vertical installation creates a minimum clamp, which means the summer pressed mode, horizontally - the maximum strong clamp. Rotating an eccentric by adjusting hexagon, you can adjust the clamp from weak to stronger and back.

Determine the need to replace the rubber sealer can be inspected and verified. You can change it with parts - at the same time you save money. Going for buying a seal, you should take a sample with you and buy a longer piece. It is better to cut up more unnecessary with a sticker than to leave the gap. Buy a high-quality rubber seal. It will be necessary to buy special glue for him. Before inserting the seal in the groove, apply glue throughout the area of \u200b\u200bcontact with the seal, glue it, close eurowindow for the period of drying the glue.

Adjusting windows and fit is made in the case of large gaps or when it is clinging behind the frame. Adjust the opening sash vertically and horizontally needed in cases:

• if it clings the top of the frame - open the sash and the short side of the M-shaped key slightly push it on the top canopy;
• if due to sagging the sash clings low part Rama, it is necessary to do the same with the lower canopy;
• if it clings the vertical part of the frame or an impost (the average vertical part of the frame), it is necessary to slightly plugging it on both canopies in the opposite place of such a contact.

How to adjust plastic windows yourself

Wind adjustment can be made independently if available required tool. The only details that can break and require the replacement are handle and sealing tires. Adjusting the window clips is transferred to the winter mode. At the same time, the handle turns with the effort, the sash is strongly pressed against the frame, heavily squeezes the seal. In the spring it will be necessary to loosen the clamp, since the opening on the ventilation occurs often, which can lead to a strong wear of the closing mechanism and seal.

To transfer to the winter mode, you must do the following steps:

1. Check the presence of thrust inside or outside the perimeter with a lit match - even a small breeze will deflect the flame.
2. If the traction is present, it is necessary to open the sash and do the adjustment of the locking pin (eccentrics).
3. Tsazfa are 3 types - oval, round with a slot under a screwdriver or under the hexagon.
4. If oval pinows are located vertically, and the eccentrics are shifted towards the frame, it is necessary to turn them into the middle position to increase the clamping force.
5. Then it is necessary to check the craving again if it remains - to switch the trough (eccentric) to the winter mode. To do this, it is necessary to check oval pin in a horizontal position, and the eccentrics are completely shifted away from the street.
6. If after checking the thrust remains - you need a replacement of the seal.
7. After replacing the seal, check the thrust when setting up the axle or eccentrics in the middle position.

How to pull the loops on plastic windows

Adjusting the upper loop is performed using a M-shaped hexagon. On the top loop there is one adjustment of the upper plank horizontally. The displacement control process is performed with a short side of the hexagon in the adjusting opening, which is located in the end of the sash. The range of offset of the upper part is in the range from -2 to +3 mm. The key rotates the screw to part of the turnover and check the ease of closing.

Lower loop adjustment is made by the same tool. The difference is that on the bottom loop, in addition to the displacement of the lower plank horizontally, there is a screw offset of the entire sash vertically. The horizontal displacement is made by the method similar to the upper loop. The vertical displacement is made with a semi-open window, for which it is necessary to insert the long side of the hexagon vertically from top to bottom into the hole of the canopy when the decorative casing is removed. Such a change is possible in the range from -2 to +2 mm.

Setting up plastic windows when shrinking at home

Strong displacement of the supporting construction elements as a result of a shrinkage of a new building can cause strong departure of the frame from the frame, to reinstall the plastic window. If the opening has twisted hard, you will have to align it or order a new eurowownau. Internal adjustments of opening and clamping mechanisms can be corrected horizontally or vertically in the range of 2-3 mm. To do this, you will need a standard set of tools:

• special key hexagon 4 mm width;
• screwdriver 4 mm;
• pliers.

How to set a horizontal and vertical axis

To align the flap horizontally or vertical, the plastic window is required in the canopy. Alignment in the horizontal plane is performed by end adjustments on the upper and lower canopy with a fully opened window. The hex key is inserted by a short side into the hole. When the key is rotated clockwise, the sash attracts to the canopy, against the clock - to the impost. The maximum adjustment range is from -2 to +2 mm.

You can adjust the displacement in the vertical position on the lower awn in cases where the sash hits the frame or to change the values \u200b\u200bof the gaps. This will require a hex key. You must open the cap on the canopy, insert the hex key with a long end down into the upper hole. Rotating a bolt clockwise, the sash can be lifted, counterclockwise - omit. The maximum adjustment range in height is from -2 to +2 mm.

What to do if the plastic window does not close

Fitted on gaps from above, bottom and sides of the sash may not be closed in two cases. The first is associated with a breakdown of the handle, the second - with the incorrect work of one of the pairs of pin-clamp. To check, you must open the window and, pressing the double opening lock by your left hand, turn the knob down. If she turned to the extreme position, then the problem of closing in one of the pairs of pin-clamp. Determine which pair does not work, you can take turns, unscrewing the clamping slats with a cross screwdriver.

?

How to adjust the handle on the plastic window

Device, diagrams and photos of the elements of accessories, adjusting bolts, movable parts of euro-mounted, methods for eliminating faults and prices can be found on the Internet on sites on this subject. Adjusting the handle is the correct installation in accordance with the list. The opening handle has four positions:

• down - closed;
• aside - openly;
• up - ventilation mode;
• in the middle position between the upper and side - partial ventilation.

Replacing faulty

If you broke the handle, you need:

• screwdriver unscrew the upper and lower screws (or screws) attachments located perpendicular to the plane of the sash;
• insert a new handle in the same position in which faulty was removed;
• fasten it with two screws (or screws);
• return the protective plate in the original position.

If the handle on the window or the balcony is breaking, it is necessary:

• slightly pull the top and bottom of the protective plate on the handle and turn it into a horizontal position;
• with a screwdriver tightly fasten the handle;
• return the protective plate at home.

All elements of the canopy and closing of the sash are outside the design. The main actions in contamination of the elements of this mechanism are its cleaning and lubrication. If the window did not open for a long time, remove the dried dirt or rust with the help of the VD-40 universal lubricant cylinder. After cleaning, the wash should be smeared to the accessories, make it setting it.

Eccentrics are round elements that are engaged with clamping straps. The axis of their mounting is shifted relative to the center of the circle, so when rotating changes the distance from the axis to the point of touch to the presser bar. With an increase in this distance, the clamp of the sash to the frame is enhanced. The rotation of the eccentrics is performed using the hex key or screwdriver. The quantity change value varies from 2 to 5 mm, depending on the design of the eccentric. Customize the press strength is necessary twice a year when switching from summer to winter mode and back.

What to do if the window handle jammed

Among possible breakdowns The locking mechanism may occur to jamming the handle. Applying great efforts to the opening handle at the same time it is not worthwhile - accessories should be preserved to extend the service life. The jamming is possible in three situations - the window is open to ventilating, open or closed. If the knob is clinically in the first two cases, there is a skew when opening or triggering a special block. If the sash hangs on the same bottom loop, you need to do the following operations:

• turn the handle up;
• putting the top loop to the frame, set the handle to the right;
• close the window and turn the knob down;
• cressing the frame to the frame, totate the handle to the up and open on the ventilation.

The rotation block triggering can occur as a result of a sharp turn of the handle to a large angle when opening. Removing the lock is made by pressing the unlocking button or rotate the corresponding lever. Its location can be found on the website of the developer of your fittings. If there are difficulties with the opening, try to press the frame very much and turn the handle.

Tight turning or jamming of the handle with a closed window is possible when shrinking and strong (more than 2-3 mm) sorting window or door opening. This is an extremely rare and complex case that can lead to a mock or breakage of the mechanism. Without construction company specialists or installers solve this problem simple adjustments Will not succeed. It is possible to join due to the lack of lubrication of the shutter mechanism. To prevent this and increase life maintenance It is advisable to produce one or twice a year.

How much is the adjustment of Eurocon in Moscow

Repair and adjustment of plastic windows is made by many firms of Moscow, St. Petersburg, other cities of Russia, who know how to adjust the PVC windows can put new spare parts. Prices for such services are different in the regions of the country, they depend on the brand of the manufacturer of fittings. The departure of the master for technical inspection and drawing up the estimate of Moscow will be from 500 to 1000 rubles. The minimum order value of Moscow is from 2000 to 3000 rubles. The cost of basic works is indicated in the table:

Name	unit of measurement	Cost, rubles
Adjusting accessories (without removal)
Door setting (without removal)
Setup, repair, partial bulkhead mechanism (without replacement of accessories)
Adjustment, repair, partial bulkhead door accessories (without replacement)
Reinstall the glass package when adjusting
Reinstalling the door glass package (the price of the glass package is not included)
Cleaning, lubrication accessories
Replacing the seal (the price of the sealer is not included)
Replacing the full set of swivel fittings
White handle / color
Main constipation swivel / swivel-folding
Purpose head
Door closer
Installing Imp

Video

Found in the text error? Highlight it, press Ctrl + Enter and we will fix everything!

Discuss

Adjusting windows for winter with your own hands

Adjustment of plastic windows on the "Winter-Summer" principle is a fairly simple procedure. You can make it with your own hands without the help of specialists. What will save your money and keep warm and comfort in the house round year. And also will extend the life of your windows.

Such adjustment of plastic windows is carried out by method: to attenuate or enhance the degree of pressed sash, by changing the position of the PSA.

Winter and summer have different degrees.

There is such a concept "Winter-Summer" on plastic windows.

This means that the adjustment on plastic windows in winter and in summer should be different different. Consider these types of window adjustment in more detail.

Example of adjusting windows on video

adjusting plastic windows

Due to the possibility of adjusting the plastic windows in the "Winter-Summer" mode, you can increase the air flow in the warm season and decrease in cold.

To adjust the plastic windows "Winter-Summer" is quite simple.

The whole process is associated with the use of a cylinder with a displaced center, pressing the sash to window frame - Eccentric (Tsazfoy).

adjusting plastic windows

It is rotated using the necessary screwdriver, and in some windows - manually, slightly pulling away a little over.

The manufacturer is provided, the so-called, "average" position of the eccentric roller,

adjusting plastic windows

which is also called "Autumn-Spring". In this case, pressing the window sash is sufficient, but not excessive.

Window adjustment before the winter season

With a decrease in temperature, especially in the transition heating period, to achieve the minimum heat loss, use the "Maximum Clim" window.

"Winter" The position of the eccentric loads the sealer as possible. For this reason, it is undesirable for newly installed new ones. In addition, receiving minimal blowing, the room loses the additional possibility of airing, because In winter, it is rarely used, and sometimes missing at all.

On the other hand, the "winter" position of the Tsazf increases the load on the seal. And this in turn does not hurt a new window, when he has lost a few elasticity.

Adjusting the window with a "maximum clamp", for extremely undesirable, because The sealing material retains the deformation and at the starting position may not return. And this is fraught with rapid wear.

Therefore, the longer the position of the eccentric is used, the greater the probability of the emergence of the seal.

To ensure maximum clips it is necessary:

• pinch a little delayed
• rotational movements to move right so
• (So \u200b\u200bthat the gap between the eccentric roller and the edge of the shaft fitting is minimal).
• If there is a notch on the roller, then with the right position - it will be directed to the seal.

Adjusting windows to the summer season

the end heating period Usually falls on sufficiently warm weather, so the load on the seal is weakened using the "summer" mode.

In this case, the impact on the seal is minimal. Therefore, this position of the eccentric is welcomed for any windows.

The adjustment of the pin for this principle somewhat increases the circulation of air indoors. However, the question of the need for such a transition is suggested. The windows in the summer are very often ventilated.
To ensure minimal clamping, the window adjustment to the summer season should be done like this:

• eccentric should be a little delayed
• rotational movements to move left so
• so that the gap between the pin and the edge of the shadow fittings turned out to be maximal.
• If there is notches on the roller, with the right position - it will be directed to the window handle.

What gives adjustment of the plastic window "Winter-Summer".

Thus, to save and extend the service life of the plastic window can adjust the "Winter-Summer". However, the degree of clamp must be increased gradually, from year to year. Only such a principle will allow not to disturb the tightness and avoid drafts. In addition, all the manipulations of the adjustment of plastic windows are so simple that they do not require special qualifications, large strengths, or a call to a specialist. Therefore, to adjust the window on the "Winter-Summer" principle with their own hands, both man and a woman.