Roller for decorative plaster: selection of the necessary modification and technology of use. Values \u200b\u200bof rollers for decorative plaster textured rollers for decorative plaster

Once the plaster served as the basis for painting works. Now it is used to decorate the interior. With textured rollers for decorative plaster The finish process does not represent any particular difficulties. Such products allow you to get different images on the surface, imitating the texture of the skin or woody bour, the effect of fur coats or stone.

Application of decorative plaster with roller (photo NO 1) is often used when finishing the premises. It is used both inside and outside the building. It has high wear-resistant qualities, water resistance, forms a very durable layer after drying. Another non-dry mixture can be applied specific patterns or plant ornaments. For this, the wizard uses a roller for texture plaster. This tool can be purchased for home and use it with your own hands. The surface will be beautiful and without any seams.

The embossed roller for decorative plaster may be the following type:

• rubber;
• wood;
• foam;
• foam;
• leather;
• plastic;
• nappy.

Rubber products (Photo NO 2) have convex drawings on their surface. If this tool is treated to the surface of the fresh layer, it will remain patterns in the form of birds and animals, plants and geometric shapes. Plastering can be done in two main ways:

• first, the finished decorative composition on the wall is applied, after easy solidification, finishing is performed;
• according to the one-layer plaster made, a new layer of roller is applied, which dips into the decorative mixture.

The solution itself should differ from the usual small grain. It should not have any solvents. They are able to destroy the foam coatings, which will leave ugly traces on the surface.

Wooden product is often made with their own hands. On its surface, sharp knife or special tools are performed by slots forming the drawing. There are rollers and industrial manufacture. But the tree absorbs moisture from plaster and gradually swells. The pattern takes not those forms. You need a roller to dry well, then continue to apply patterns.

The foam product is an analogue of the rubber tool, but cheaper. The quality of it is very low, the service life is short. Polyfoam is capable of flattening when working. This leads to the fact that the pattern on the processed wall may not be exactly the one that is expected.

Application ready A tool made of leather allows you to get the effect of marble. Elastic skin leaves beautiful divorces on the surface, resembling stone coating. This effect is used when applying Venetian plaster. The roller should be made only from genuine leather. Artificial can or do not leave tracks on the surface, or spoil the plaster layer.

Plastic roller is cheaper than rubber fellow. With it, many patterns and various textures are created. This embossed tool on its surface has holes and holes that form bulges on the wall. The disadvantage is that plastic is capable of deforming with time, to be covered by cracks.

The darous rollers are able to create the effect of fur coats on the wall (photo NO 3). The pile is of different lengths, natural and artificial. Its value ranges from 2 to 25 mm. The longer the pile, the Mokhnate coat on the wall surface. To keep the veil on the case must be firmly, otherwise they can spoil the expensive decorative coating.

Applying decorative plaster

For each room, we need their own patterns and structural roller. In the kitchen and in the hallway you can imitate brickwork. In the bedroom, this drawing is unlikely to look beautiful. You can apply the decorative mixture with homemade tools if you failed to purchase the necessary in the store.

You can make a factory roller with a foam. Patterns are cut out with a conventional sharp knife. If you need texture texture, it is better to use natural materials. On a simple, the foam roller is wound and fixed by threads strip of a canvas fabric. The decorative mixture on the wall can be processed even with appliant means, which is convenient to use the roller roller or massage rollers.

How to make a coating of plaster with your own hands? First you need to prepare the walls. Their surface must be cleared of the old coating, from dust, then process the primer. After drying, the solution is applied to the spacure for alignment of the walls. This is done with spatulas width from 40 to 60 cm. When the composition hardens, you can apply decorative plaster.

The dry mixture is connected to water according to the instructions and are mixed well until the necessary homogeneous consistency is achieved. Application of plaster on the walls is carried out by a thin layer of 2-4 mm. It is done again with a wide spatula. After 10 minutes, the solution begins to thicken. This is the start time of work as a textured roller. It is rolled from top to bottom without much pressure. There should be a certain pattern immediately.

The finish is better to carry out together: one person shall apply a plaster solution, the other works with a roller. Further surface treatment is carried out after 48 hours. The dried wall can be completely painted or highlight individual patterns. Make it can be a roller with a short or long pile.

When working with textured tools, you must remember and execute several rules:

• do not strongly press the tool;
• to do the second track on the border of the previous strip, not allowing the overlap;
• all movements to make in one direction;
• with a long work, the structural tool is wearing, it must be changed on time;
• a very embossed pattern after drying can be smoothed by a wet grinding grid.

Conclusion on the topic

Usually decorative plaster is used in public buildingsbut also at home can be done own forces. To do this, you need to purchase or make your own hands a relief roller for plaster with patterns and decorative material in the form of a powder or a finished solution. The mixture is sold in a hermetic container. After applying the roller plaster, you do not need to use respirators or gloves, since the material is non-toxic and does not carry the danger to human health.

After the work, textured rollers for decorative plaster required to rinse well in running water and dry.

You can create a unique embossed pattern on the walls and ceiling. For this, in addition to the material, textural rollers will be required. They can be made of different materials: foam rubber, rubber, plastic, and so on. The easiest way to buy a product in the store, but you can make a woolproof roller with your own hands.

It will be necessary, but a whole roller from any material and any size. It is very important that the product handle is preserved. The remaining details can be easily found in any house.

With the help of a rope

For the manufacture of roller, you need to take a conventional clothes rope or any cord and wind it on the workpiece. The more often the cord will be checked, the denser will be the pattern. Can be used various methods winding, make intersection and so on. The result will be a relief pattern from the depression. Before using a homemade roller, it is recommended to check it on little plot Wall or unnecessary plywood sheet.

With the help of a knife

If a foam roller remains from finishing in an acceptable state, it can also be used. To do this, you need to take a stationery or sharply sharpened ordinary knife and cut stripes, squares or any other arbitrary figures. The more they are, the larger the texture of the drawing. In the same way, the roller from the foam can be treated. If there is an unnecessary new product from the foam rubber, it is enough just to drag it to the thread so that wrinkles formed.

Using a polyethylene package

This is the easiest and minimum cost method of manufacturing textured products. You need to take an old roller and lock on it with a scotch meal package. The folds create a complex unique pattern from thin embossed strips. Instead of a package, you can use hair gum, fabric trimming, a grid for storing vegetables, dense paper.

Making a roller for decorative color using a plastic bag

From rubber rolik

It is also possible to manufacture a textured roller for painting walls of rubber products. To do this, you need to take a regular rubber roller and using a copy paper to apply a specific pattern on it. Then this pattern must be cut into a knife. You can also use conventional rubber, but its thickness should be at least 5 mm. It is necessary to take care that the relief drawing on the product makes a single whole, while the lines must be wave-like. At the end of the rubber sheet with relief fixed on a cylindrical billet.

Fact roller Easy to create with a conventional knife, which you need to cut the desired pattern on the rubber instrument

From foil

To make a factory roller yourself, you will need the following:

1. Dense foil. Finding such a foil is difficult for sale, but you can use fragments of packing of dairy or some other products.
2. Acrylic putty.
3. Crochet hook.

The manufacture of the roller in this case occurs according to the method of chasing. First of all, it is necessary to carefully clean the surface of the foil from the residues of food and fat. Then the picture should be applied on the foil, which is planned to be transferred to the ceiling or walls. Next, you need to take a hook for knitting or any other product similar shape and squeeze the relief drawings on the foil on the previously applied lines.

Important! During the chasing, it is necessary to observe a certain distance between the embossed lines. In order for the drawing subsequently turned out to be blurred, it is recommended to retreat with 5 mm.

It is necessary to apply an acrylic putty on the back of the product, and then press it to the surface of the roller. At this stage, it is important to give a cylindrical shape as quickly as possible until the putty has time to grab. Then you need to leave the workpiece drying (the frost time is indicated by the manufacturer on the material packaging). The last step is to glue foil to the roller on quick-drying glue.

From fine rubber and silicone glue

Before making a roller, you must prepare:

• sheet of thin rubber;
• silicone sealant and gun for applying it;
• marker.

First you need to clean the rubber and carefully degrease the surface. Then the pattern should be marked or a pencil, which is planned to decorate walls or ceiling. Next, you need to charge the gun with a sealant and gently apply it on the markup. It is better to stop the choice on a simple pattern without subtle lines and weave. Figure is perfect for waves, leaves or simple geometric shapes.

With the help of sealant on the surface of the tool, you can create a convex pattern or impression, thanks to which the decorative effect is achieved on the wall.

To make a factory roller with your own hands, you can use any product on the surface of which there is a relief pattern. For example, buttons with great embossed, leaving artificial plants, various gypsum products. The selected item is lubricated with vegetable oil, applied to the rubber layer of silicone sealant, make an impression and leave to dry. It is possible to clean the product only after drying the sealant. Then the rubber sheet is glued on the roller.

Roller with scratch

The above describes the methods of making textured rollers that imply the use of old tools. But there is an opportunity to make it yourself from scratch. First of all, it is necessary to make the base - a cylindrical part. There are several options for blanks for the base:

• Wooden rolling pin. This is the most suitable product. If the rod is equipped with a handle, it needs to be cut, leaving only a smooth cylinder. Then drill in the center through hole in which you need to insert a metallic rod or wire. You can use the handle from the old product.

Homemade instrument From wooden rolling

• Plastic tube. For these purposes, it will take a pipe with a diameter of 5 cm and 10 cm long. After trimming the workpiece, it is necessary to make plugs for the product ends, they are recommended to cut out of plastic. Then you should stick the plugs and cut into them the holes for the handle.

The manufacture of textured roller is a fairly simple process. It cannot be said that in this way you can save a lot of money, but one of a kind roller will help create a really original coating.

When it comes to beautiful finish walls, a good solution become rollers for decorative plaster along with use this material As an internal coating. Of course, the spectacular texture can be obtained and with the help of other tools, for example, inflicting light brummers with a narrow spatula, but it is most practical that it is roller. It remains only to find out which forms takes this tool, and what results with it can be achieved.

What are the rollers for decorative plaster

Initially, the decoration of the walls was performed solely with the help of paints, the plaster was needed only to apply frescoes on it. In this regard, the rollers were used only by paint, from fur, and later from the foam rubber, foam and others artificial materials. But over time, new techniques for decorating plastering coatings appeared, especially for the "Venetian", which required the use and radical change tools. All sorts of applicators, stamps, combs, and, of course, textured rollers, the basis of which became a foam large-scale prototype.

Based on materials, the aforementioned foam and foam, as well as rubber and leather rollers for decorative plaster are distinguished. More exotic options are possible, for example, homemade, carved from wood, that is, piece work. By invoice, the surface of the tool data can be mimicing marble divorces, brickwork, wood fibers and even a mine weaving. Also used to emboss simple and complex patterns, for which a repeating pattern is applied on the working surface, the end of which goes to the beginning. A large foam rubber creates a roughness of varying degrees of depth.

Textured rollers for imitation of various materials

If you want to create a relief on the wall surface, covering it with plaster, it is necessary that some structure be on the surface of the tool. To obtain protruding prints, textured rollers should be with recesses reflecting the selected pattern, if, on the contrary, the pattern on the wall surface should be squeezed, use the working surface with a relief pattern. In particular, if we need imitation brick masonry, we take the usual smooth rubber roller, make two ring channels, separating the working surface into three equal parts, after which there are transverse excavations on each of them in checked order. We get rectangular writing in each row, they will be bricks.

To simulate marble, it is enough to take a roller with a nozzle from the root skin or fabric. At the same time, during the operation of the movement, uniform, without releasing the tool from the surface as long as possible. Another way to get a structural roller with your own hands is to wind the rubber nozzle with a harness from the same material, making the turns in an arbitrary direction. Such an uneven working surface can be depicted wood fibers. Perhaps the direction of the turns will have to be corrected to obtain greater reliability of the texture. And finally, placing a piece of coarse tissue on the rubber nozzle, you can obtain imitation of textile upholstery. Almost any imitation can be obtained by a foam nozzle, applying the desired pattern on its surface.

Roller structural rubber for complex patterns

As a child, many are keen on the manufacture of rubber stamps, which can be used more than once, rubbing a graphite pencil rod or ink puff pens. Approximately the same is the roller structural rubber, only the pattern on it is closed around the cylindrical working surface. Once such rollers began to produce so that the hosts can do insistent on the wallpaper under the painting. However, over time appeared ready Wallpaper With different patterns, and a special device for the decor turned out to be unnecessary. It was useful tool to finish the walls of the plaster.

But if the usual nozzle with a small relief can be easily used to apply a sufficiently liquid decorative composition, is it suitable for this purpose a figured roller, with a pronounced pattern? Unfortunately no. The fact is that the textured nozzle with small irregularities allows you to capture a rather thick layer of the mixture, and in the process of its application layer it turns out somewhere thicker, and somewhere thinner. If very protruding figures of the drawing are cut on the working surface, only they are imprinted on the wall, the rest of the space will not be covered with plaster.

But this kind of tools are perfectly suitable for obtaining a picture on the already decorated surface. Not news that even the most fast-drying makeup freezes about twenty minutes. This time is quite enough to take a roller in the hands and roll it on the surface of the finished site. It is only necessary to observe one rule: the movement should be performed from top to bottom, with the same speed over the entire length of the decorating strip. The next passage of the tool must be completed close to the previous one, without indents and adhesion.

How to make structural roller with your own hands

Today, the tools for creating a textured pattern on a freshly mixed surface is in a free sale. They are made of rubber and have a strongly speaker over the base of the stamp in the form of a picture. However, it is much more pleasant to do something unusual independently, as a result, get a unique pattern. So what will be needed for this. First, the usual rubber roller for smoothing the wallpaper. Secondly, you need to find a dense thick rubber thick about a centimeter (you can take a couple of dozen erasers, but it is in extreme cases). And finally, we need glue for rubber.

From the rubber sheet or erase cut the figure, for example, a plant leaf. If the pattern fragments are sticking with large gaps, the role form does not play the role, otherwise it is better to make a fragment so that there is no difference, which of the parties will become a working one. The next element in the continuation of the plant theme will, for example, flower. You can make stems, buds, berries, the content of the pattern does not matter, the main thing is that it is continuous around the entire cylindrical surface of the tool nozzles. All parts are fixed with glue from the end to the end, the metal rod (BEGEEL), on which the nozzle rotates, is usually bent so that it does not completely prevent the change in the nozzle diameter.

The dimensions of machine tools consisting of handles, bohels (metal rod) and roller can be different: short, in the range of 30 centimeters, medium, from 35 to 45 centimeters, and long, from 50 centimeters and more. Special extension handles are also available, from 70 centimeters to 4 meters.

In order for the pattern to be as high as possible, it is desirable to round the working surface of all pasted parts. This will allow the figured elements into the surface of the plaster gently, without disturbing the print with sharp edges. Do not hurry and create a pattern right away as soon as the plaster covers the wall. The fact is that the fresh mixture will stick to the tool relief, clogged between closely located elements and, accordingly, remain on the roller. It is better to wait about ten minutes (or longer, depending on the finishing material used) to give the composition a little silent.

Create a unique interior and comfort in the house is easily and interesting for a patterned roller for the decor of the walls. Art painting Any surfaces now become available to all. Want to decorate the walls with a classic or original openwork pattern? You need only a few materials: paint favorite color, patterned rollers and frame for them. This simple set of each room will give their own charm. Any meager, naked walls for a couple of strokes will find a unique look.

Most importantly, any person can use patterned rollers. Even without experience in this area. A large range of rollers and detailed descriptions of each of them will help to make this difficult choice. In our store you can choose the goods to your taste. The cost of rollers is justified by quality and durability. In the online store "Color" presented rollers only from the most best manufacturersTime proven.

Pattern of a new life in your hands

Patterned rollers You can buy in our online store, from the variety of drawings will choose the one that will delight you every day. It is worth discarding all doubts and diversify your life with bright colors and interesting patterns. Perhaps this choice will be the most difficult stage in the creative process of decorating. Most likely, you will want to buy several patterned rollers for painting walls. The rest is the case of technology. Such information about the correct use of patterned rollers can be found in the description of each sentence. In the same way, you will draw inspiration to the beginning of work. The process itself will bring pleasure, because you all do it yourself. And the price of a patterned roller for the decoration of the walls will strengthen your desire to diversify the interior when the time to work will take at least. Do not deny yourself so pleasure!

Decorative plaster or paint has recently been extremely popular, as it allows you to give the room stylish original interior. And to work with these finishing materials use a factory roller. And what are their varieties and what are their features, we will now try to find out.

Textual rollers and features of their use

To work with a textured roller, you will not need special skills and knowledge. It is enough just to prepare paint and rushing the tool in a special cuvette. It must be done in order to avoid the inclination when the surface is stained. Yes, and paint will in this case will fall to a uniform layer. And the plaster - without clots and lumps on the surface.

Note! Extremely undesirable to use the same tool for different types coatings. That is, for textured paint, we use one kind of tool, and for plaster - respectively, the other. Similar tools can be bought in the store or do it yourself.

Materials for the manufacture of decorative rollers

The modern tools between the material type are distinguished. To date, the market shows the following types of decorative rollers:

There are also analogues with a base of foam rubber, foam and fabric. Poropolone options are used to primer the first layer for subsequent decor. They are also great for creating on the surface of bubbles. Fabric analogs, for the manufacture of which the plush soft fabric is used, form embossed traces on the wall (patterns). Devices based on polyfoam resemble a rubber analog. But at the same time it must be remembered that the foam is short-lived.

Classification of decorative rollers on the texture pattern

Each tool has a variety of structure, with which the final drawing is obtained. It can be imitation natural materials or arbitrary ornaments. All tools are divided into two types.

Types of tools:

Also, the tools are divided into the width of the roller. The minimum width reaches 30 centimeters. The wider the roller, the faster to apply texture paint. But a narrow roller allows you to create a clear original structure.

How to make a decorative roller

Some finishing tools are very expensive. Therefore, the manufacture of roller with their own hands from the primary materials will become excellent and inexpensive output from the current situation. And how to do it, you will learn now.

First method

In this case, we will need: the rope is a linen and an unnecessary old roller with a strong handle and a reliable roller. Mix the rope on the roller and secure the ends. Please note that depending on the winding frequency you can adjust the texture of strips and patterns on the wall.

Option number two

For this method, we will need an old foam roller. We make cuts in several places with sharp scissors and get a textural tool with the original effect.

Third way

Another method is as follows: Change the roller with polyethylene, then fix it with the thread. And to make traces of texture instead of polyethylene, you can use the usual tape.

Fourth option

Skillful masters are offered to make an independent structural roller, to create which it will be necessary to show a fantasy and a little bit of patience and perfection. And in order to achieve high-quality coverage, you need to think in detail your idea. You can also use templates when covering the surface with finishing material. So, to obtain structural plasters it is worth considering next option Purified tool creation:

In a word, you can create an absolutely any structure on the wall with the help of girlfriend.

Machinery appliances Structural roller

To keep the plaster for a long time, you need to pre-process the surface. If you plan to use a factory roller for painting the surface then there is no need to paint the surface in the main color. However, it must be remembered that when working with a structural analogue, a similar procedure is mandatory. Otherwise, the drawing on the roller will stretch in the wrong direction of the finished mixture.

Prayes the surface correct

To achieve the optimal result, you should use the following tips:

To create texture with imitation "fur coats", textile fibers and marble crumbs, you can use a relief roller for applying paints with a textured base. Finishing material It is recommended to apply onto the walls, running the pre-instrument in the paint container. If surplus began to form in the process of work, they must be removed using a spatula.

Using decorative rollers, you can create original designwho will not give up the work of a professional. And all that will be required of you is to choose a tool with necessary structure And to enable fantasy - and the result obtained will certainly please you with your magnificence.