Dressing table in Shuflade with their own hands. Dressing table with your own hands - a great gift for your beloved. How to make from girlfriend

Every woman dreams of a small town, where she can decompose all their accessories and cosmetics. Buying a ready-made dressing table is not always possible. This is due to its high cost and not always suitable sizes. As for the individual order, it may be even more expensive. Therefore, it is more expedient to make a dressing table with your own hands. It's simple, the main thing is to give a sufficient amount of time and think over its design. The design of the table should include a working surface, shelves, retractable boxes and a mirror.

Dimensions of the toilet table.

Additionally, such a dressing table can be equipped with lamps. They can also be used as night lights if they are equipped with brightness adjustment system.

In order to make a dressing table, you need to use a laminated chipboard. Coloring is selected at its discretion. If you wish, you can combine several colors. If possible, you can order details, to do this, provide dimensions to the appropriate workshops in which you will cut the necessary elements of the table. If there is no such possibility, you can cope with it yourself, at home. For this you need to get a special tool.

Tools that will be needed to make a table with your own hands:

Dressing table assembly scheme.

schuropvutht, you can use a drill;
lobzik electric;
roulette;
building corner, it is enough to be 30 cm length;
drills required dimensions - 8 and 5 mm in diameter;
screwdriver, it is very important to purchase a hexagon model;
iron;
pencil for the mark, hammer, you will also need sandpaper.

If the details of the table were ordered, you can immediately start assembling. If this process is performed independently, it is necessary to start with measurements and drawing contours to the sheet of chipboard. It is very important to measure correctly and only then cut off. In order to make the dressing table perfect, it is better to make measurements several times.

For a toilet table will be enough to use a thickness of a sheet of 16 mm.

After all parts are cut with an electrolybiz, the ends must be cleaned with sandpaper. This should be done carefully not to damage the lamination.

Accessories for assembly

The next step is the assembly. Almost all cabinet furniture has the same fasteners. They can be purchased at any construction store in the fittings department. For a table with a shelf and drawers It will take such a set of accessories:

General view of the dressing table.

confirmation of 5x70 mm in size can be purchased with a reserve;
self-samples of 4x16 mm;
self-dimensions of 4x25 mm;
for drawers, you need to purchase roller guides, size and quantity depends on the size of the design;
knobs for drawers;
soft kant for ends;
the melamine edge on adhesive basis is recommended to take with a reserve;
metal furniture corners;
glue for the mirror, you can use mechanical fasteners;
for the handles it is necessary to pick up screws.

Features of the assembly process

If the design of the table involves curved lines, it is not worth a hurry during the dipping. It is from how items will be prepared will depend on appearance Designs.

Prepared details must be treated with the end side. To do this, they need to be projected. This can be done using the usual "moment" glue. Such a reception will make the edges of the chipboard more durable.
After complete drying, you need to apply another layer of glue and put on a kant. The soft cannon is used only on the top countertop. For finishing the ends, which are not processed by Crate, use the melamine edge.
In order to glue it, the ends also need to be cleaned. The melamine edge is glued by the usual iron. Having attached one end to the edge to the end, we smoothed a well-heated iron (up to 3-4 power). Iron you need to spend from above several times until it glued. Press the dry cloth well. After cooling unnecessary items to cut. It is very important to use a stupid object that does not damage the laminated layer. The face is inspired by shallow emery paper.
Ready details can be collected. A roller guides for drawers are installed in the disassembled form. The assembly of the entire design is made by configress. The first is going to the base of the table, then the department with drawers or cabinet. All branches are connected. In the process of assembly, it is necessary to check the corners of 90 degrees.
The final stage is the installation of the mirror. Previously enshrines on the prepared part of the chipboard. A more reliable option for consolidation is mechanical holders, which are screwed into the base of the chipboard.
The whole design with the mirror is attached under the table top. For further strength, you must install the guides that will hold the design with the mirror. The correctly installed mirror should not be movable.

For greater convenience in such a table, you can equip lamps with daylight. Make a dressing table with your own hands is quite real, the main thing is to comply with the recommendations and be patient and attentive. And the table made with your own hands will please your favorite woman.

You need to care for any girl. Sometimes it is very difficult to find one or another cosmetics, a mirror or comb. Toilet table will help you to cope with this little problem. It can be performed in the form of a tremor with a mirror or without it, and even with backlight. This furniture can be made not only multifunctional, but also beautiful, which will significantly transform the interior of your apartment. Most often, such a product is installed in the bedroom, corridor or bathroom. It is a very convenient thing due to the fact that all the necessary items will be at your hand. It is not easy to make a dressing table with your own hands, but it is possible if you start working with the construction of a simpler design. Today we will tell you how to do it.

Dressing table with your own hands - Preparation and materials

Before starting the product, you need to fulfill a specific action plan: to conduct preparatory work and purchase required Material And other components. Let's consider in order each of these stages.

Preparatory work

Without execution preparatory work You are unlikely to work out a beautiful, stable and durable design. Below is an instruction that is suitable for an absolutely any toilet table. So let's get acquainted with it:

Carefully think over the design of the structure and correspondence with the general picture of the interior.

Important! It is desirable that the table be performed in calm colors that would like the immediate hostess.

Create a drawing of the dressing table with sizes. We indicate the desired length, width, depth, height, size, and number of shelves. In the case of furniture with a built-in mirror we write on paper and its parameters. If the table will have additional lighting, then we note the location of future lamps with a description of the method of their attachment. Similar drawings can be made independently or take ready schemes from the Internet.

Important! The lockers and shelves pay special attention, because their size and number directly depend on the dimensions of the product and from your wishes. It is important to consider all the nuances: where you put cosmetics, first aid kit, books and other necessary things. If you have a lot of things, then add open side shelves to the design.

We choose a mirror if it will be available. According to its parameters, we will pick up the attachments that will keep it.

Important! It is advisable to stay on the mirror with thick walls so that you are not worried about its integrity and safety.

That material that you choose for the manufacture of the skeleton of the trumma, you need to polish well, to handle edges with high quality, and then close with plastic corners.

Materials and tools

It is not so difficult to make a simple dressing table. For example, you can make a small chest, and the mirror attach in parallel to the wall. The only thing you need is drawers for accessories.

List of materials to choose from for the manufacture of frame, side walls, bottoms and shelves of this product:

Chipboard sheets or LDSP 16 mm thick. These are the most common materials in furniture manufacturing. They have a number of advantages: it is inexpensive, they have a slight weight and easily treatable at home.
MDF sheets. Considered expensive because of their high Quality, efficiency and durability.
Wood. For such a material, only those craftsmen are taken, who have experience in joinery. Wood is easily processed, but a milling machine is needed for drinking parts.
Plywood or fiberboard. Use for the manufacture of the bottom of the boxes and the rear wall of the furniture.

Required mounting elements:

Confirmates 5x70 mm.
Self-sample size 4x16 mm and 4x25 mm.
Metal furniture corners.
Roller guides for free movement of drawers.
Accessories for doors and boxes.
Plastic edge on adhesive basis.

Instruments:

Drill or shurtpers with a set of nozzles.
Electrolovka for cutting sheets of chipboard, LDSP, MDF.
Drills with a diameter of 5 and 8 mm.
Construction corner.
Roulette.
Screwdriver to twist confirmation.
Natural paper of varying degrees of grain.

Additional accessories and details:

Mirror of the desired size.
Plastic inserts for flaps (for glass - glass).
LED Strip Light.
Decorative panels.

Table for cosmetics do it yourself without a mirror

This is the easiest option that is ideal for a beginner. So, you are presented to your attention a detailed master class on the manufacture of such a small chest under accessories:

We assign ready-made sketches of the details of our future product to the chipsticks.

Important! You can easily chop the sheets in almost any construction store for a small fee. So you will be sure about the quality of specialists. If you still do not have such an opportunity, then cut the material into parts using an electric jig.

We clean the ends of every detail with sandpaper: first large grain, and then shallow.

Important! Do not be upset at the form of chips on the edge of the sheets, because at the end of all work, any flaws will hide the end ribbon.

Soil two times the ends to give greater strength to the edge. For this, the glue "moment" is well suited. We dress up the tabletop soft cant, and then you take the ends with a special melamine edge, which we apply to the edge and stroke the iron.
We collect the framework of our table: worktop, side walls, legs, rear wall. Arrow holes for fastening all elements with each other. Fix the details of confirmation, check the angles with building level. After made sure proper assembly Constructions, tighten the confirmation with a suitable key.
Duplicate metal corners lateral walls and support legs of our product.
Now we collect boxes. All side parts are drilled into the plane, and in the end - the front and rear parts. We collect a table on the confirmates, check the quality of the assembly, and then tighten the fastening with a screwdriver. Fix with small nails plywood bottom.
We fix one roller guide to side self-testers, and its second retaliatory part is to the walls of the couch. Inwaying boxes in installed guides.
Since our table with doors, then for the installation of the loops we will need a forstner drill with a diameter of 35 mm. We make holes under the loop depth of 12.5 mm. Fix loops with durable screws. Fix the loop to the sash with ordinary self-drawing.
Serve on the front part of the drawers and doors of the product hole for the handles, and then firmly fix the fittings.

Build a dressing table with a mirror

This method is a bit more complicated than the previous chest without a mirror, but it is also quite possible to make it. Let's consider the two main methods of its manufacture.

The first method:

We cut the rear wall not from the Fiberboard sheet, but from the LDSP with the prepared framework for the future mirror. It can be as a functional device or be a decorative frame of the most different forms.
Fix the purchased mirror in the frame with the help of plastic holders. For these purposes, you can use "liquid nails" or bilateral tape.

The second method:

From the sheets of plywood cut the desired shape under the mirror. It can be rectangular, square, round or curly.
Fresh mirror " liquid nails"To the carved canvase.
We are screwed while another detail to the rear wall of the base of the previously made toilet table. We carry out this work with self-draws, screwing them as much as possible to the top with the mirror.

Dressing table with mirror and backlit with your own hands

In the dresser for accessories, built-in lighting can perform one of two functions - practical or decorative. For the last option, you will need a LED tape, preferably colored. It is placed on the edge of the table, along the support legs or the bottom of the furniture.

Important! Installing such lighting is very simple: the places of possible cutting and connections are noted on the tape. Do not forget that the tape works from the power grid, the voltage of which should be at least 12 W. So you will create a slightly muted light in the coffee table.

The technique of making a backlit couch:

Collect out wooden boards 20 mm thick and 90 mm width is the main framing in size of our mirror. All parts are combined with a joinery glue. Drink the ends at an angle of 45 degrees. Fix the design in the corners with metal corners.
Serve in the frame of the hole, which are needed to install bulb cartridges. We glue the outer frame from the finest rails. It is she who will hide the wires of our backlight.
I fix the furniture corners to the base, then put the mirror on them. We connect the cartridges in parallel to each other.
Mobile product in the desired color. We are waiting for complete drying.
We derive the power cord through one velocked hole.
Now we screw the bulbs into the cartridges and check the operation of the lighting.

Now you know how to make a dressing table with your own hands. According to the above instructions, it is not so difficult to perform, especially since it is possible to start a simpler model for a start, and then improve it.

Dressing table is very useful thingthat will be the perfect fit for the bedroom. However, if at the moment there is no possibility to purchase this piece of furniture, you can try to make it yourself. How to make a dressing table with your own hands? This is a completely saturated task that is simplified by using the instructions proposed below. If you consider yourself a novice master, choose as much as possible simple schema And proceed to work. If you have knowledge and experience, it will be more interesting to find and embody a complex lady with numerous boxes and shelves.

Before you equip the dressing table with your own hands, you should prepare the following materials:

the chipboard (the laminated version of the same material is also suitable). These options are best suited for independent manufacture Furniture, as you have a small mass and are quite affordable. In addition, they can be processed without making significant efforts. Standard - plates with a thickness of 16 mm. Alternatively, you can take MDF, made according to GOST, which is characterized by a high degree of efficiency and long service life. If this material is more suitable, keep in mind that it is characterized by a higher price;
wood. If you have some joinery experience, you can choose this stuff to create a dress for a girl. Choose those rocks that are easiest to be processed, for example, pine, characterized by relatively low cost. Do not forget that special equipment will be required to work with wood, at a minimum, a device for milling work;
plywood sheet, which will be required for the manufacture of the bottom of the boxes, as well as the rear wall of the table.

Do not forget about tools and special devices. The list includes:

fasteners (configmatics, screws);
roller guides that will be needed for equipment boxes. If you do not want to make boxes and plan to do the shelves, then this element will not need at all;
furniture corners made of metal;
furniture fittings;
edge for finishing works;
screwdriver (instead, a drill with a set of nozzles is suitable;
electric jigsaw (it is useful for cutting wood-chip plates);
roulette for performing accurate measurements;
construction corner;
granular paper;
screwdriver for working with confirmates.

In addition to those subjects that have already been listed, additional elements may be required, for example, a mirror if you plan to make a stylish dressing table with a mirror to put it in the bedroom. Decorative wood accessories will not be superfluous. They will give the finished product stylish and modern view, The women's room will be changed dramatically, if you put a beautiful table made in it, made personally. It remains hope that you can choose the items you need.

In order to cope with the manufacture of a dressing table, listen to several valuable advice. First, the key to quality work is the thoroughness of its conduct. Even if you have chosen the most concise photo model, try to pull out each item with special accuracy so that there are no problems with fit.

1 2 3 4

Secondly, take advantage of the schemes, observing all the features that contain a drawing.

If you decide to enable any additional element The structure of the design or change the dimensions, it will have to take additional efforts: buy accessories, replace one material to others and so on.

This significantly complicates the work. There is hope only that the novice master is lucky, and he will cope with the task.

How to equip a dressing table?

1 2 3 4

Instructions for assembling the standard product will help create a presentable and stylish interior subject:

The determinant with the dimensions that will have ready product (This parameter is especially important as height), as well as the place where the furniture will be. Standard is a model of 80 cm high. However, the size of the toilet tables may vary depending on the area of \u200b\u200bthe room and other circumstances.
Make a project or pick up ready, watching photos on our website. Transfer each element to special paper for drawings.
Attach the prepared templates prepared on the wood-chipboard, cut the parts on them using the electric jigsk for this purpose. If the structure does not include too complex parts, then even a beginner master does not have any special experience can cope with the work.
End blanks Treat emery paper. If, when performing this procedure, chips were formed, then it is better to disguise with a special tape. Face elements twice cover the primer to make the edge more durable. To do this, it is recommended to use high-quality glue.
On the tabletop dressing the kant, plunder the ends with the melamine edge. Clearly fix it on the edge, and then treat the heated iron.
Collect individual elements forming furniture frame. Create a countertop, racks, legs and rear walls with each other. To do this, do the holes at the outlined points, and then fix the items using the confirmates. Check the corners of the building: if everything is performed correctly and correctly, tighten the fasteners with the key.
Collect boxes, drilled separate item and crossing them using confirmates. Check carefully, whether the standard is met, and then tighten the fastener with a screwdriver. Plywn bottom to secure small carnations. Attach the guide products and response parts in the appropriate places, and after insert the box.
On the front, do the holes for the handle and fix the accessories.
If the design assumes the presence of a couch closing on the door, you will have to install overhead loops. To fix them, make holes with a depth of 12.5 mm, attach a loop using screws. To the door accessories, screw the screws.

If you wish to create a highlightest path with your own hands, which will decorate the interior, acquire lED ribbonsconsisting of small lamps. Lighting is a difficult procedure, try to work with extreme caution when you create a dress for toilet toilet. Alternatively, you can choose small light bulbs if you have some skills of the electrician and installer. Otherwise, hope remains only to a specialist, which is worth useful to avoid accidents.

How nice will decorate the bathroom to the toilet table, which is made with your own hands. He will add comfort and stylish the interior of the room and pride to the owner of the house for his work. In addition, it will be accurately fitted under the size, which is not always able to buy it in furniture salons. Of course, not every master has "golden hands", but still you need to try to make a dressing table yourself.

It is necessary to start with the development of a drawing drawing drawing sketch. To do this, measure the height, length and width in the place of the intended installation of this interior detail. On the checkered paper, it is drawn by its housing in the 3D version. Depending on the size, we calculate the location of the number and size of the boxes. But at the same time, consider that under the table top there should be a free place for the legs during the seating on a chair behind the toilet table.

Boxes can be located on one side in a row or one horizontally under the table top. The amount of them is selected depending on the size of the case. Types of boxes can also be changed. They can be wide or narrow and long. It all depends on the size and your imagination.

On video: phased instruction

Choose material and fittings

A chipboard is suitable for a toilet table. All materials for the manufacture of furniture must be impregnated with special compositions to protect against harmful moisture.

Accessories is also better to buy moisture-resistant. If you do not know which materials and accessories need to be bought, contact sellers consultants with a request to assist. They will answer all your questions and familiarize themselves with new items.

Council. Stroyarkets provide services for sawing materials for the manufacture of furniture. Therefore, refer to the store for providing this service. As a result, you will get ready-made details with clean cuts. Alone to cut the material in the same way as in the supermarket, you can hardly succeed.

Elements of fittings and fasteners that you will need:

Saws 4x25 - "-.
Roller guides for boxes.
Metal corners, furniture.
Confirmates 5x70 (sold hundreds, will be useful);
Saws 4x16 and 4x25.
Pens for boxes.
Screws for fastening the handles.
Kant and melamine edge treated with inside glue.

All these products are sold in building supermarkets. Contact you for help during selection to sellers. They know exactly what you need and offer to buy all the necessary products.

Starting the assembly is needed from the case and separately each box. After attaching roller guides, you can already install boxes. All sections are processed by edging and melamine edge.

These articles will also be interested..